MC9S08JM60CGT Freescale Semiconductor, MC9S08JM60CGT Datasheet - Page 243

• Manufacturer Part Number: MC9S08JM60CGT
• Description: IC MCU 8BIT 60K FLASH 48-QFN
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08JM60CGT

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, LIN, SCI, SPI, USB
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 37
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-QFN
• Processor Series: S08JM
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: SCI/SPI
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 37
• Number Of Timers: 8
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMOJM, DEMOJMSKT, DEMOFLEXISJMSD, DEMO9S08JM16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 12-bit
• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 24MHz
• Total Internal Ram Size: 4KB
• # I/os (max): 37
• Number Of Timers - General Purpose: 8
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: QFN EP
• Package: 48QFN EP
• Family Name: HCS08
• Maximum Speed: 24 MHz
• Operating Supply Voltage: 3.3|5 V
• For Use With: DEMOJM - KIT DEMO FOR JM MCU FAMILYDEMOJMSKT - BOARD DEMO S08JM CARD W/SOCKET
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Chapter 15
16-Bit Serial Peripheral Interface (S08SPI16V1)
15.1
Introduction
The 8- or 16-bit selectable serial peripheral interface (SPI) module provides for full-duplex, synchronous,
serial communication between the MCU and peripheral devices. These peripheral devices can include
other microcontrollers, analog-to-digital converters, shift registers, sensors, memories, etc.
The SPI runs at a baud rate up to the bus clock divided by two in master mode and up to the bus clock
divided by four in slave mode. Software can poll the status flags, or SPI operation can be interrupt driven.
The SPI also supports a data length of 8 or 16 bits and includes a hardware match feature for the receive
data buffer.
The MC9S08JM60 series have two serial peripheral interface modules (SPI1 and SPI2). The four pins
associated with SPI functionality are shared with PTB[3:0] and PTE[7:4]. See
Appendix A, “Electrical
Characteristics,” for SPI electrical parametric information.
15.1.1
SPI Port Configuration Information
By default, the input filters on the SPI port pins will be enabled (SPIxFE=1), which restricts the SPI data
rate to 6 MHz, but protects the SPI from noise during data transfers.To configure the SPI at a baud rate of
6MHz or greater, the input filters on the SPI port pins must be disabled by clearing the SPIxFE in SOPT2.
and also enable the high output drive strength selection on the affected SPI port pins.
MC9S08JM60 Series Data Sheet, Rev. 3
Freescale Semiconductor
243