ATMEGA162V-8PU Atmel, ATMEGA162V-8PU Datasheet - Page 39

• Manufacturer Part Number: ATMEGA162V-8PU
• Description: IC AVR MCU 16K 8MHZ 1.8V 40DIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA162V-8PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: EBI/EMI, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Processor Series: ATMEGA16x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: JTAG/SPI/USART
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 35
• Number Of Timers: 4
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Minimum Operating Temperature: - 40 C
• Package: 40PDIP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 8 MHz
• For Use With: ATSTK600-TQFP44 - STK600 SOCKET/ADAPTER 44-TQFPATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Oscillator Calibration
Register – OSCCAL
2513K–AVR–07/09
Time-out. For more information on the pre-programmed calibration value, see the section
bration Byte” on page
Table 11. Internal Calibrated RC Oscillator Operating Modes
Note:
When this Oscillator is selected, start-up times are determined by the SUT Fuses as shown in
Table
Table 12. Start-up Times for the Internal Calibrated RC Oscillator Clock Selection
Note:
• Bit 7 – Res: Reserved Bit
This bit is reserved bit in the ATmega162, and will always read as zero.
• Bits 6..0 – CAL6..0: Oscillator Calibration Value
Writing the calibration byte to this address will trim the Internal Oscillator to remove process vari-
ations from the Oscillator frequency. This is done automatically during Chip Reset. When
OSCCAL is zero, the lowest available frequency is chosen. Writing non-zero values to this regis-
ter will increase the frequency of the Internal Oscillator. Writing 0x7F to the register gives the
highest available frequency. The calibrated Oscillator is used to time EEPROM and Flash
access. If EEPROM or Flash is written, do not calibrate to more than 10% above the nominal fre-
quency. Otherwise, the EEPROM or Flash write may fail.
Bit
Read/Write
Initial Value
SUT1:0
10
00
01
11
(1)
12. XTAL1 and XTAL2 should be left unconnected (NC).
1. The device is shipped with this option selected.
1. The device is shipped with this option selected.
Start-up Time from Power-
down and Power-save
R
7
–
0
CKSEL3:0
0010
6 CK
6 CK
6 CK
234.
CAL6
R/W
(1)
6
CAL5
R/W
5
Device Specific Calibration Value
CAL4
R/W
4
Additional Delay from
Reset (V
Reserved
CAL3
R/W
4.1 ms
65 ms
3
CC
–
= 5.0V)
CAL2
R/W
Nominal Frequency
2
8.0 MHz
CAL1
R/W
Recommended Usage
BOD enabled
Fast rising power
Slowly rising power
1
ATmega162/V
CAL0
R/W
0
OSCCAL
“Cali-
39