ST7FLIT15BY0B6 STMicroelectronics, ST7FLIT15BY0B6 Datasheet - Page 46

• Manufacturer Part Number: ST7FLIT15BY0B6
• Description: IC MCU 8BIT 2K FLASH 16-DIP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST7FLIT15BY0B6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 11
• Program Memory Size: 2KB (2K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 7x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-DIP (0.300", 7.62mm)
• Processor Series: ST7FLIT1x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: ST7FLITE-SK/RAIS, ST7MDT10-DVP3, ST7MDT10-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 7 Channel
• For Use With: 497-8427 - BOARD DEMO USB LI-ION ST7260E2497-5049 - KIT STARTER RAISONANCE ST7FLITE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

ST7LITE1xB
POWER SAVING MODES (Cont’d)
Figure 31. AWUFH Mode Flow-chart
46/159
1
(AWUCSR.AWUEN=1)
HALT INSTRUCTION
(Active-Halt disabled)
N
WATCHDOG
WDGHALT
RESET
1
INTERRUPT
Y
1)
ENABLE
3)
256 OR 4096 CPU CLOCK
OR SERVICE INTERRUPT
0
FETCH RESET VECTOR
AWU RC OSC
AWU RC OSC
MAIN OSC
PERIPHERALS
CPU
MAIN OSC
PERIPHERALS
CPU
AWU RC OSC
MAIN OSC
PERIPHERALS
CPU
I[1:0] BITS
I[1:0] BITS
I[1:0] BITS
N
CYCLE
RESET
Y
WATCHDOG
DELAY
DISABLE
2)
XX
XX
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
5)
ON
ON
ON
ON
10
4)
4)
Notes:
1. WDGHALT is an option bit. See option byte sec-
tion for more details.
2. Peripheral clocked with an external clock source
can still be active.
3. Only an AWUFH interrupt and some specific in-
terrupts can exit the MCU from HALT mode (such
as external interrupt). Refer to Table 5, “Interrupt
Mapping,” on page 37 for more details.
4. Before servicing an interrupt, the CC register is
pushed on the stack. The I[1:0] bits of the CC reg-
ister are set to the current software priority level of
the interrupt routine and recovered when the CC
register is popped.
5. If the PLL is enabled by option byte, it outputs
the clock after an additional delay of t
Figure
13).
STARTUP
(see