Z8F3221PM020SG Zilog, Z8F3221PM020SG Datasheet - Page 107

• Manufacturer Part Number: Z8F3221PM020SG
• Description: IC ENCORE MCU FLASH 32K 40DIP
• Manufacturer: Zilog
• Series: Encore!® XP®r

Specifications of Z8F3221PM020SG

• Core Processor: Z8
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, IrDA, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 29
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 40-DIP (0.620", 15.75mm)
• Processor Series: Z8F322x
• Core: eZ8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 29
• Number Of Timers: 3
• Operating Supply Voltage: 3 V to 3.6 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: Through Hole
• Development Tools By Supplier: Z8F64200100KITG, ZENETSC0100ZACG, ZUSBSC00100ZACG, Z8F64210100ZDA, Z8F64210100ZDP, Z8F64210100ZDV, Z8F64220100ZDA, Z8F64220100ZDV, Z8F6422AR00ZEM, Z8F6422VS00ZEM, Z8F6421AN00ZEM
• Minimum Operating Temperature: 0 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: 770-1002 - ISP 4PORT ZILOG Z8 ENCORE! MCU269-4643 - KIT DEV Z8 ENCORE XP 28-PIN269-4630 - DEV KIT FOR Z8 ENCORE 8K/4K269-4629 - KIT DEV Z8 ENCORE XP 28-PIN269-4628 - KIT DEV Z8 ENCORE XP 8-PIN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 269-4257; Z8F3221PM020SG

Table 47. Watchdog Timer Approximate Time-Out Delays
PS019918-1206
WDT Reload Value
FFFFFF
000004
Watchdog Timer Refresh
Watchdog Timer Time-Out Response
(Hex)
When first enabled, the Watchdog Timer is loaded with the value in the Watchdog Timer
Reload registers. The Watchdog Timer then counts down to
instruction is executed by the eZ8 CPU. Execution of the WDT instruction causes the
downcounter to be reloaded with the WDT Reload value stored in the Watchdog Timer
Reload registers. Counting resumes following the reload operation.
When the 64K Series devices are operating in DEBUG Mode (through the On-Chip
Debugger), the Watchdog Timer is continuously refreshed to prevent spurious Watchdog
Timer time-outs.
The Watchdog Timer times out when the counter reaches
Watchdog Timer generates either an interrupt or a Reset. The WDT_RES Option Bit
determines the time-out response of the Watchdog Timer. For information on
programming of the WDT_RES Option Bit, see
WDT Interrupt in Normal Operation
If configured to generate an interrupt when a time-out occurs, the Watchdog Timer issues
an interrupt request to the interrupt controller and sets the WDT status bit in the Watchdog
Timer Control register. If interrupts are enabled, the eZ8 CPU responds to the interrupt
request by fetching the Watchdog Timer interrupt vector and executing code from the
vector address. After time-out and interrupt generation, the Watchdog Timer counter rolls
over to its maximum value of
counter is not automatically returned to its Reload Value.
WDT Interrupt in STOP Mode
If configured to generate an interrupt when a time-out occurs and the 64K Series devices
are in STOP mode, the Watchdog Timer automatically initiates a Stop Mode Recovery and
generates an interrupt request. Both the WDT status bit and the STOP bit in the Watchdog
Timer Control register are set to 1 following WDT time-out in STOP mode. For more
information on Stop Mode Recovery, see
WDT Reload Value
16,777,215
(Decimal)
4
FFFFFH
(with 10 kHz typical WDT oscillator frequency)
and continues counting. The Watchdog Timer
Reset and Stop Mode Recovery
1677.5 s
Typical
400 μs
Approximate Time-Out Delay
Option Bits
000000H
on page 191.
000000H
Z8 Encore!
Description
Maximum time-out delay
Product Specification
Minimum time-out delay
. A time-out of the
unless a WDT
Watchdog Timer
on page 45.
®
64K Series
94