MC908JK3EMDWER Freescale Semiconductor, MC908JK3EMDWER Datasheet - Page 119

• Manufacturer Part Number: MC908JK3EMDWER
• Description: MCU 8BIT 128RAM 4K FLASH 20-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908JK3EMDWER

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 15
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 12x8b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 20-SOIC (7.5mm Width)
• Processor Series: HC08JK
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 2
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908JL16E, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 12 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

The vector fetch or software clear and the return of all enabled keyboard interrupt pins to 1 may occur in
any order.
If the MODEK bit is clear, the keyboard interrupt pin is falling-edge-sensitive only. With MODEK clear, a
vector fetch or software clear immediately clears the keyboard interrupt request.
Reset clears the keyboard interrupt request and the MODEK bit, clearing the interrupt request even if a
keyboard interrupt pin stays at 0.
The keyboard flag bit (KEYF) in the keyboard status and control register can be used to see if a pending
interrupt exists. The KEYF bit is not affected by the keyboard interrupt mask bit (IMASKK) which makes
it useful in applications where polling is preferred.
To determine the logic level on a keyboard interrupt pin, disable the pull-up device, use the data direction
register to configure the pin as an input and then read the data register.
12.4.1 Keyboard Initialization
When a keyboard interrupt pin is enabled, it takes time for the internal pull-up to reach a logic 1. Therefore
a false interrupt can occur as soon as the pin is enabled.
To prevent a false interrupt on keyboard initialization:
An interrupt signal on an edge-triggered pin can be acknowledged immediately after enabling the pin. An
interrupt signal on an edge- and level-triggered interrupt pin must be acknowledged after a delay that
depends on the external load.
Another way to avoid a false interrupt:
12.5 Keyboard Interrupt Registers
Two registers control the operation of the keyboard interrupt module:
Freescale Semiconductor
1. Mask keyboard interrupts by setting the IMASKK bit in the keyboard status and control register.
2. Enable the KBI pins by setting the appropriate KBIEx bits in the keyboard interrupt enable register.
3. Write to the ACKK bit in the keyboard status and control register to clear any false interrupts.
4. Clear the IMASKK bit.
1. Configure the keyboard pins as outputs by setting the appropriate DDRA bits in the data direction
2. Write 1s to the appropriate port A data register bits.
3. Enable the KBI pins by setting the appropriate KBIEx bits in the keyboard interrupt enable register.
•
•
register A.
Keyboard status and control register
Keyboard interrupt enable register
Setting a keyboard interrupt enable bit (KBIEx) forces the corresponding
keyboard interrupt pin to be an input, overriding the data direction register.
However, the data direction register bit must be a 0 for software to read the
pin.
MC68HC908JL3E Family Data Sheet, Rev. 4
NOTE
Keyboard Interrupt Registers
119