MC908JK3EMDWER Freescale Semiconductor, MC908JK3EMDWER Datasheet - Page 54

• Manufacturer Part Number: MC908JK3EMDWER
• Description: MCU 8BIT 128RAM 4K FLASH 20-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908JK3EMDWER

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 15
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 12x8b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 20-SOIC (7.5mm Width)
• Processor Series: HC08JK
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 2
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908JL16E, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 12 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

System Integration Module (SIM)
OSC1
PORRST
4096
32
32
CYCLES
CYCLES
CYCLES
2OSCOUT
OSCOUT
RST
IAB
$FFFE
$FFFF
Figure 5-7. POR Recovery
5.3.2.2 Computer Operating Properly (COP) Reset
An input to the SIM is reserved for the COP reset signal. The overflow of the COP counter causes an
internal reset and sets the COP bit in the reset status register (RSR). The SIM actively pulls down the
RST pin for all internal reset sources.
To prevent a COP module time-out, write any value to location $FFFF. Writing to location $FFFF clears
the COP counter and stages 12 through 5 of the SIM counter. The SIM counter output, which occurs at
least every 4080 2OSCOUT cycles, drives the COP counter. The COP should be serviced as soon as
possible out of reset to guarantee the maximum amount of time before the first time-out.
The COP module is disabled if the RST pin or the IRQ pin is held at V
while the MCU is in monitor
TST
mode. The COP module can be disabled only through combinational logic conditioned with the high
voltage signal on the RST or the IRQ pin. This prevents the COP from becoming disabled as a result of
external noise. During a break state, V
on the RST pin disables the COP module.
TST
5.3.2.3 Illegal Opcode Reset
The SIM decodes signals from the CPU to detect illegal instructions. An illegal instruction sets the ILOP
bit in the reset status register (RSR) and causes a reset.
If the stop enable bit, STOP, in the mask option register is zero, the SIM treats the STOP instruction as
an illegal opcode and causes an illegal opcode reset. The SIM actively pulls down the RST pin for all
internal reset sources.
5.3.2.4 Illegal Address Reset
An opcode fetch from an unmapped address generates an illegal address reset. The SIM verifies that the
CPU is fetching an opcode prior to asserting the ILAD bit in the reset status register (RSR) and resetting
the MCU. A data fetch from an unmapped address does not generate a reset. The SIM actively pulls down
the RST pin for all internal reset sources.
MC68HC908JL3E Family Data Sheet, Rev. 4
54
Freescale Semiconductor