UPD78F0551MA-FAA-AX Renesas Electronics America, UPD78F0551MA-FAA-AX Datasheet - Page 470

• Manufacturer Part Number: UPD78F0551MA-FAA-AX
• Description: MCU 8BIT 16-SSOP
• Manufacturer: Renesas Electronics America
• Series: 78K0/Kx2-Lr

Specifications of UPD78F0551MA-FAA-AX

• Core Processor: 78K/0
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: I²C, LIN, UART/USART
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 9
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

78K0/Kx2-L
R01UH0028EJ0400 Rev.4.00
Sep 27, 2010
Note If “reception as 0 parity” is selected, the parity is not judged. Therefore, bit 2 (PE6) of asynchronous serial
Cautions 1. To start the transmission, set POWER6 to 1 and then set TXE6 to 1. To stop the transmission,
interface reception error status register 6 (ASIS6) is not set and the error interrupt does not occur.
Figure 14-5. Format of Asynchronous Serial Interface Operation Mode Register 6 (ASIM6) (2/2)
2. To start the reception, set POWER6 to 1 and then set RXE6 to 1. To stop the reception, clear
3. Set POWER6 to 1 and then set RXE6 to 1 while a high level is input to the R
4. TXE6 and RXE6 are synchronized by the base clock (f
5. Set transmit data to TXB6 at least one base clock (f
6. Clear the TXE6 and RXE6 bits to 0 before rewriting the PS61, PS60, and CL6 bits.
7. Fix the PS61 and PS60 bits to 0 when used in LIN communication operation.
8. Clear TXE6 to 0 before rewriting the SL6 bit. Reception is always performed with “the number of
9. Make sure that RXE6 = 0 when rewriting the ISRM6 bit.
ISRM6
PS61
clear TXE6 to 0, and then clear POWER6 to 0.
RXE6 to 0, and then clear POWER6 to 0.
set to 1 and RXE6 is set to 1 while a low level is input, reception is started.
transmission or reception again, set TXE6 or RXE6 to 1 at least two clocks of the base clock after
TXE6 or RXE6 has been cleared to 0. If TXE6 or RXE6 is set within two clocks of the base clock,
the transmission circuit or reception circuit may not be initialized.
stop bits = 1”, and therefore, is not affected by the set value of the SL6 bit.
CL6
SL6
0
1
0
1
0
1
0
0
1
1
Character length of data = 7 bits
Character length of data = 8 bits
Number of stop bits = 1
Number of stop bits = 2
“INTSRE6” occurs in case of error (at this time, INTSR6 does not occur).
“INTSR6” occurs in case of error (at this time, INTSRE6 does not occur).
PS60
0
1
0
1
Enables/disables occurrence of reception completion interrupt in case of error
Does not output parity bit.
Outputs 0 parity.
Outputs odd parity.
Outputs even parity.
Transmission operation
Specifies character length of transmit/receive data
Specifies number of stop bits of transmit data
CHAPTER 14 SERIAL INTERFACE UART6
XCLK6
) after setting TXE6 = 1.
Reception without parity
Reception as 0 parity
Judges as odd parity.
Judges as even parity.
XCLK6
Reception operation
) set by CKSR6.
Note
X
D6 pin. If POWER6 is
To enable
456