ISL6267HRZ Intersil, ISL6267HRZ Datasheet - Page 23

• Manufacturer Part Number: ISL6267HRZ
• Description: IC PWM CTRLR MULTIPHASE 48TQFN
• Manufacturer: Intersil

Specifications of ISL6267HRZ

• Applications: Converter, AMD Fusion™ CPU GPU
• Voltage - Input: 4.75 V ~ 5.25 V
• Number Of Outputs: 2
• Voltage - Output: 0.0125 V ~ 1.55 V
• Operating Temperature: -10°C ~ 100°C
• Mounting Type: *
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Dynamic Operation
Core VR and Northbridge VR behave the same during dynamic
operation. The controller responds to VID-on-the-fly changes by
slewing to the new voltage at the fixed 7.5mV/µs slew rate.
During negative VID transitions, the output voltage decays to the
lower VID value at the slew rate determined by the load.
SVI_L low command prompts the controller to enter DE mode.
Overvoltage protection is blanked during VID down transition in
DE mode until the output voltage is within 60mV of the VID value.
During load insertion response, the Fast Clock function increases
the PWM pulse response speed. The controller monitors the
VSEN pin voltage and compares it to 100ns-filtered version.
When the unfiltered version is 20mV below the filtered version,
the controller knows there is a fast voltage dip due to load
insertion, and it issues an additional master clock signal to
deliver a PWM pulse immediately.
The R
output voltage is insensitive to a fast slew rate input voltage
change.
Protections
Core VR and Northbridge VR both provide overcurrent,
current-balance and overvoltage fault protections. The controller
also provides over-temperature protection. The following
discussion is based on Core VR and also applies to Northbridge VR.
The controller determines overcurrent protection (OCP) by
comparing the average value of the droop current (I
internal current source threshold as Table 6 shows. It declares OCP
when I
For overcurrent conditions above 1.5x the OCP level, the PWM
outputs immediately shuts off and PGOOD goes low to maximize
protection. This protection is also referred to as way-overcurrent
protection or fast overcurrent protection for short-circuit
protections.
The controller monitors the ISEN pin voltages to determine
current-balance protection. If the ISEN pin voltage difference is
greater than 9mV for 1ms, the controller will declare a fault and
latch off.
The controller takes the same actions for all of the previously
describe fault protections: de-assertion of PGOOD and turn-off of
the high-side and low-side power MOSFETs. Any residual inductor
current decays through the MOSFET body diodes.
The controller declares an overvoltage fault and de-asserts PGOOD if
the output voltage exceeds the VID set value by +250mV. The
ISL6267 immediately declares an OV fault, de-asserts PGOOD,
and turn on the low-side power MOSFETs. The low-side power
MOSFETs remain on until the output voltage is pulled down below
the VID set value when all power MOSFETs are turned off. If the
output voltage rises above the VID set value +250mV again, the
protection process is repeated. This behavior provides the
maximum amount of protection against shorted high-side power
MOSFETs while preventing output ringing below ground.
All of the previously described fault conditions can be reset by
bringing ENABLE low or by bringing V
3
droop
™ modulator intrinsically has voltage feed-forward. The
is above the threshold for 120µs.
23
DD
below the POR
droop
) with an
ISL6267
threshold. When ENABLE and V
levels, a soft-start occurs.
Table 8 summarizes the fault protections.
FB2 Function
The FB2 function is only available for Core VR or Northbridge VR
in 2-phase configuration.
Figure 19 shows the FB2 function. A switch (called FB2 switch)
turns on to short the FB and the FB2 pins when the controller is in
2-phase mode. Capacitors C3.1 and C3.2 are in parallel, serving
as part of the compensator. When the controller enters 1-phase
mode, the FB2 switch turns off, removing C3.2 and leaving only
C3.1 in the compensator. The compensator gain increases with
the removal of C3.2. By properly sizing C3.1 and C3.2, the
compensator can be optimal for both 2-phase mode and 1-phase
mode.
When the FB2 switch is off, C3.2 is disconnected from the FB pin.
However, the controller still actively drives the FB2 pin voltage to
follow the FB pin voltage such that C3.2 voltage always follows
C3.1 voltage. When the controller turns on the FB2 switch, C3.2
is reconnected to the compensator smoothly.
The FB2 function ensures excellent transient response in both
2-phase and 1-phase mode. If the FB2 function is not used,
populate C3.1 only.
Adaptive Body Diode Conduction Time
Reduction
In DCM, the controller turns off the low-side MOSFET when the
inductor current approaches zero. During on-time of the low-side
MOSFET, phase voltage is negative, and the amount is the
Overcurrent
Phase Current
Unbalance
Way-Overcurrent
(1.5xOC)
Overvoltage +200mV
Over-Temperature
VSEN
2-PHASE MODE
CONTROLLER
FAULT TYPE
IN
C2
R1
R3
TABLE 8. FAULT PROTECTION SUMMARY
VREF
FB2
FB
FIGURE 19. FB2 FUNCTION
C1
C3.1
C3.2
FAULT DURATION
E/A
R2
PROTECTION
Immediately
BEFORE
120µs
1ms
COMP
VSEN
DD
1-PHASE MODE
CONTROLLER
return to their high operating
PGOOD latched
PWM tri-state,
PGOOD latched
low
low. Actively pulls
the output
voltage to below
VID value, then
tri-state.
400µs
IN
C2
PROTECTION
R1
ACTION
R3
VREF
FB2
FB
C1
January 31, 2011
C3.1
C3.2
E/A
R2
ENABLE
toggle or
VDD toggle
RESET
FAULT
FN7801.0
N/A
COMP