1-1532127-9 Tyco Electronics, 1-1532127-9 Datasheet - Page 10

• Manufacturer Part Number: 1-1532127-9
• Description: Conn Microminiature D SKT 21 POS Solder ST Thru-Hole 21 Terminal 1 Port
• Manufacturer: Tyco Electronics
• Type: Microminiature Dr

Specifications of 1-1532127-9

• Gender: SKT
• Termination Method: Solder
• Mounting: Through Hole
• Body Orientation: Straight

6
Technical and Performance Data
(Applicable to MCK, MCD and MCDM unless otherwise noted)
Electrical
Contacts — Pin 24 AWG twist pin,
Socket 24 AWG precision machined
barrel, Wire Range 24 AWG to 30 AWG
solid and stranded.
Contact Resistance — (voltage drop)
25 millivolts max. at 3 amps, 77°± 7.4°F
[25°± 3° C].
Current Rating — 3 amps max. per
contact.
Dielectric Withstanding Voltage —
Volts RMS 60 Hz at room ambient.
At sea level 600V solder pots, 750V wire
terminations & transition blocks.
At 70,000 ft. [21,336 m] 150V solder
pots, 200V wire terminations & transi-
tion blocks.
Insulation Resistance — 5,000
megohms min. (@ 500 VDC) at ambient
room temperature.
Magnetic Permeability — 2 mu max.
Mechanical
Contact Spacing — .050 [1.27mm]
centers.
Contact Engagement &
Separation — Standard contact
engaging force is 6.0 oz. [1.67N] (8.0 oz.
[2.22N] max.). Separation force is 0.5
[.14N] oz. min.
Mating Force Maximum —
Calculated as 10 oz. times the number
of contacts.
Twist Pin, Pin and Socket
Contacts
The contact spring member
normally found in socket
contacts has been eliminat-
ed by creating a breathing
helical spring principle on
the pin contact — smaller,
more durable contacts
can be manufactured
economically.
Catalog 1308638
Revised 8-05
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Microminiature D Connectors
MCK/MCD/MCDM Series Metal and Plastic Shell Connectors
Environmental
Temperature Range —
-67°F to 257°F [-55° C to +125°C] for
MCK/MCD, -67°F to 302°F [-55°C to
+150°C] for MCDM.
Vibration — No discontinuity in
excess of 1 µ sec. when tested in accor-
dance with MIL-STD-1344, Method
2005, test Condition IV.
Solderability — Connectors shall
pass the test requirements of MIL-STD-
202, Method 208
Shock — No discontinuity in excess of
1 µ sec. when tested in accordance with
MIL-STD-1344, Method 2004, test
Condition E.
Durability — No mechanical or electri-
cal defects detrimental to the function of
the connectors after 500 cycles of mat-
ing and unmating.
Humidity — After exposure to humidi-
ty as specified by MIL-STD-1344,
Method 1002, Type II, IR shall be 1
megohm min. following step 7a of
Method 1002 and 1000 megohms min.
after 24 hours of conditioning per
Method 1002.
Salt Spray — Connectors shall meet
the performance requirements of contact
resistance, mating and unmating forces,
and contact retention after being subject-
ed to the 48-hour 5% solution salt spray
test per MIL-STD-1344, Method 1001,
Condition B.
Fluid Immersion — Unmated con-
nectors after being fully immersed in one
of the following fluids, for the prescribed
time, will mate at a force of 10 oz.
MIL-DTL-83513 — Only the descriptive legend in bold italic is applicable to current MIL-DTL-83513 configurations;
MIL-DTL-83513/1 through /4 — MCK metal shell; MIL-DTL-83513/6 through /9 — MCD plastic shell.
In addition, MIL-DTL-83513 solid copper wire termination is specified 25 AWG, 0.5; and 1.0 [25.4] lengths only and
stranded insulated wire termination is specified 26 AWG, 18.0 [457.2] and 36.0 [914.4] lead lengths only. Hardware for
MIL-DTL-83513 configurations is specified separately by the M83513/5-XX designation. M83513/1 through /4 and /6
through /9 specify no hardware (B). Mounting/mating hardware is shown on page 14 with the applicable military
nomenclature. The MICRODOT catalog part number for a MIL-DTL-83513 configuration may be constructed
to include the desired hardware.
See pages 31-35 for M83513/ cross reference.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
[2.78N] times the number of contacts
or less: Perchloroethylene, 2 hours;
Lubricating oil per MIL-L-23699,
20 hours.
Insert Retention — Inserts will with-
stand a 50 lb. [34N/cm
load in either direction.
Crimp Termination Tensile
Strength — (Unassembled contacts
with crimped stranded wire terminations)
Wires will not pull out of contacts when
the following axial loads are applied:
24 AWG, 5 lbs. [22.24N]; 26 AWG,
4 lbs. [17.79N]; 28 AWG, 3 lbs.
[13.34N]
Outgassing — When tested in accor-
dance with SP-R-0022, Total Mass Loss
(TML) shall be less than 1.0% and
Volatile Condensable Material (VCM)
shall be less than 0.1% of the original
specimen.
Materials and Finishes
Contacts — Copper alloy plated with
.000050 [.00127] gold over copper flash
per MIL-G-45204 Type II.
Hardware — see pages 14 and 15.
MCK-Metal Shell —
Insulator — Liquid crystal polymer
Interfacial Seal — Fluorosilicone Rubber
Body Shell — Aluminum alloy-high
Cadmium per QQ-P-416
Nickel, electroless per AMS 2404
(LCP) per ASTM D5138, or
Polyphenylene sulfide GST-40F per
ASTM D5927 or MIL-M-24519
per MIL-R-25988 (socket side only)
grade plated
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
2
] per square inch
Wire range 24-36 AWG solid & stranded.
Transition Block Shell —
Liquid crystal polymer (LCP) per ASTM
Potting Material — Epoxy, Black
MCD-Plastic Shell —
Insulator/Body — Polyester, glass filled
Wire Terminations —
Solid copper per QQ-W-343 gold plated
Stranded TEFLON insulated per MIL-W-
Stranded TEFLON insulated per MIL-W-
Solid copper per QQ-W-343, solder
MCDM-Metal Shell —
Insulator — Diallyl Phthalate per MIL-
Body Shell — Aluminum alloy—high
D5138, or Polyphenylene sulfide
GST-40F per ASTM D5927 or
MIL-M-24519
per MIL-M-24519, Liquid crystal
polymer (LCP) per ASTM D5138, or
Polyphenylene sulfide GST-40F per
ASTM D5927 or MIL-M-24519
per MIL-G-45204
16878
22759/11, /33
dipped (Transition block)
M-14, Type SDG-F
grade, nickel plated
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967