1-1532127-9 Tyco Electronics, 1-1532127-9 Datasheet - Page 144

• Manufacturer Part Number: 1-1532127-9
• Description: Conn Microminiature D SKT 21 POS Solder ST Thru-Hole 21 Terminal 1 Port
• Manufacturer: Tyco Electronics
• Type: Microminiature Dr

Specifications of 1-1532127-9

• Gender: SKT
• Termination Method: Solder
• Mounting: Through Hole
• Body Orientation: Straight

140
Catalog 1308638
Revised 8-05
www.tycoelectronics.com
Technical and Performance
Data
Electrical
Contact Resistance – .003 - .008
ohms
Current Rating – 1 amp max. per
contact
Dielectric Withstanding Voltage –
Volts RMS 60 Hz at room ambient con-
ditions. At sea level 500V. At 70,000 ft.
150V.
Insulation Resistance – 5000
megohms min. (@ 500 VDC) at room
ambient conditions.
Magnetic Permeability – 2 mu max.
Mechanical
Contact Engagement & Separation
– Engaging force is 6.0 oz. max.
Separation force is 0.5 oz. min.
Mating Force Maximum –
Calculated as 10 oz. multiplied by the
number of contacts.
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
NANONICS Connectors
Nano-Miniature Connectors
Environmental
Temperature Range – -200° C to
+200° C
Shock – No discontinuity in excess of 1
µ sec. when tested in accordance with
MIL-STD-1344, Method 2004.1, Test
Condition E.
Vibration – No discontinuity in excess
of 1 µ sec. when tested in accordance
with MIL-STD-1344, Method 2005.1,
Test Condition IV.
Solderability – Connectors shall meet
the test requirements of MIL-STD-202,
Method 208.
Durablity – No mechanical or electrical
defects detrimental to the function of the
connectors after 500 cycles of mating
and unmating, without the use of
hardware.
Humidity – After exposure to humidity
as specified by MIL-STD-1344, Method
1002.2, Type II, IR shall be 1 megohm
min. (@ 100 VDC) within 2 hours of
conditioning and 1000 megohms min.
(@ 100 VDC) after 24 hours of condi-
tioning.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Salt Spray – Connectors shall meet the
performance requirements of contact
resistance, mating and unmating forces,
and contact retention after being subject-
ed to the 48 hour 5 % solution salt
spray test per MIL-STD-1344, Method
1001, Condition B.
Fluid Immersion – Unmated connec-
tors after being fully immersed in one of
the following fluids, for the prescribed
time, will mate at a force of 10 oz. multi-
plied by the number of contacts or less:
Perchloroethylene, 2 hours; Lubricating
oil per MIL-L-23699, 20 hours.
Crimp Tensile Strength –
(Unassembled contacts with crimped
stranded wire terminations) Wires will
not pull out of the contacts when the fol-
lowing axial load is applied: #30 AWG,
2 lbs.
Thermal Vacuum Outgassing –
Connectors shall have a maximum total
mass loss (TML) of 1.0 % of the original
specimen mass and a maximum collect-
ed volatile condensable materials
(CVCM) content of 0.1 % of the original
specimen mass when tested in accor-
dance with SP-R-0022A.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
Material and Finish
Contacts – BeCu alloy plated with gold
per MIL-G-45204 Type II over nickel per
QQ-N-290.
Plastic Insulators and Shells –
30% glassed filled Liquid Crystal
Polymer (LCP).
Metal Shells – 6061-T6 Aluminum
with electroless nickel plating per MIL-
C-26074. Stainless steel and gold plat-
ed shells are also available.
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967