1-1532127-9 Tyco Electronics, 1-1532127-9 Datasheet - Page 121

• Manufacturer Part Number: 1-1532127-9
• Description: Conn Microminiature D SKT 21 POS Solder ST Thru-Hole 21 Terminal 1 Port
• Manufacturer: Tyco Electronics
• Type: Microminiature Dr

Specifications of 1-1532127-9

• Gender: SKT
• Termination Method: Solder
• Mounting: Through Hole
• Body Orientation: Straight

Performance Data Summary
For LEPRA/CON Connectors
Catalog 1308638
Revised 8-05
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Coaxial Connectors
LEPRA/CON Ultra-Miniature Connectors
Mechanical
Captive Contacts — Terminated con-
nector contacts captivated from move-
ment in both directions.
Cable Retention —
10 lb. min. when properly assembled to
RG196/U and RG178/U cable.
Recommended Coupling Torque
(Threaded Interface) —
24 inch/ounces max.
Recommended Receptacle
Mounting Torque (All Series) —
24 inch/ounces max.
Typical Cable Acceptance
Dimensions — Inner conductor: .012
[0.31] nom. Dielectric: .039 [0.99] max.
Shield: .059 [1.50] max. Jacket: .081
[2.06] max.
Contact Protection (Unmated) —
Twist pin contact protected from damage
by insulator. Tube socket protected by
connector housing.
Assembly Methods
Straight Plugs & Jacks — Cable
Inner Conductor: Crimped to contact.
Cable Shield: Crimped under housing.
Right-Angle Plugs — Cable Inner
Conductor: Soldered to contact. Cable
Shield: Crimped under housing.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Environmental
Temperature Range (Continuous
Service) — -85°F to +392°F
[-65°C to +200°C].
Vibration
204, Test Condition B (15 G peaks). No
physical damage or electrical disconti-
nuities in excess of 1 microsecond.
Shock
213, Test Condition H. No physical dam-
age or electrical discontinuity after
shock.
Thermal Shock — MIL-STD-202,
Method 107, Test Condition C.
Moisture Resistance
202, Method 106.
Salt Spray
101, Test Condition B (48 hours).
Electrical
Impedance — Designed to be com-
patible with 50 Ohm coaxial cable
RG178/U.
Dielectric Withstanding Voltage —
450 volts RMS at sea level, 250 volts
RMS at 50,000 ft [15,240 m], 150 volts
RMS at 70,000 ft. [21,336 m]
Contact Resistance — 8 milliohms
max., D.C.
Contact Capacity — 3 amps, D.C.
Insulation Resistance — 10
Megohms min. @ 500 volts D.C.
1,2
— MIL-STD-202, Method
1,2
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
1
— MIL-STD-202, Method
— MIL-STD-202, Method
1
— MIL-STD-
4
Voltage Standing Wave Ratio
(VSWR) — Typical 50 Ohm Series, 1.2
Maximum to 2 GHz.
Materials
Housing, Nut, Ferrule — Brass per
ASTM-B-16.
Insulator — TEFLON per
ASTM-D-1710.
Pin & Socket Contact — Copper
Alloy.
Crimp Sleeve — Copper Alloy.
Lockwasher — #425 Bronze Alloy.
Plating
Contacts, Housing, Nut, Ferrule,
Crimp Sleeve, Lockwasher —
Gold per MIL-G-45204, Type II, Grade
C, Class 1.
Notes:
1
2
3
Screw-On Series, threaded interface.
Tyco Electronics recommends the
use of safety wired connectors in
vibration and shock environments.
See individual specifications with
wire holes.
VSWR is a system specification.
Where performance is critical,
purchase Tyco Electronics cable
assemblies with Screw-On connec-
tors (See page 129) and specify
VSWR testing and mating
connector part numbers.
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
3
117
4