1-1532127-9 Tyco Electronics, 1-1532127-9 Datasheet - Page 116

• Manufacturer Part Number: 1-1532127-9
• Description: Conn Microminiature D SKT 21 POS Solder ST Thru-Hole 21 Terminal 1 Port
• Manufacturer: Tyco Electronics
• Type: Microminiature Dr

Specifications of 1-1532127-9

• Gender: SKT
• Termination Method: Solder
• Mounting: Through Hole
• Body Orientation: Straight

112
Performance Data
Summary
For Gold Plated Crimp Style
Coaxial Connectors
Catalog 1308638
Revised 8-05
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Coaxial Connectors
Gold Plated Crimp Style Coaxial Connectors
Mechanical
Captive Contacts — Terminated con-
nector contacts captivated from move-
ment in both directions.
Cable Retention —
50 Ohm connectors, 15 lb. min.
70 Ohm connectors, 25 lb. min.
93 Ohm connectors, 25 lb. min.
Recommended Coupling Torque
(Threaded Interface) —
8 inch/pounds max. [.904 Nm]
Recommended Receptacle
Mounting Torque (Threaded
Interface) — 8 inch/pounds max.
[.904 Nm]
Contact Protection (Unmated) —
Pin contact protected by coupling nut.
Socket protected by insulator and
housing.
Assembly Methods
Straight Plugs & Jacks — Cable
Inner Conductor: Crimped to contact.
Cable Shield: Crimped under housing.
Right-Angle Plugs — Cable Inner
Conductor: Crimped to contact. Cable
Shield: Crimped under housing.
Environmental
Temperature Range (Continuous
Service) — -80°F to +392°F.
[-62°C to +200°C].
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Vibration
204, Test condition B (15 G peak). No
physical damage or electrical disconti-
nuities in excess of 1 microsecond.
Shock
213, Test Condition H. No physical dam-
age or electrical discontinuity after
shock.
Thermal Shock — MIL-STD-202,
Method 107, Test Condition C.
Moisture Resistance
202, Method 106.
Salt Spray
101, Test Condition B (48 hours).
Electrical
Impedance — Designed to be com-
patible with 50, 70, or 93 Ohm miniature
coaxial cable.
Dielectric Withstanding Voltage —
1000 volts RMS at sea level.
Contact Resistance — 4 milliohms
max., D.C.
Contact Capacity — 3 amps, D.C.
Insulation Resistance — 5 x 10
Megohms min. @ 500 volts D.C.
Voltage Standing Wave Ratio
(VSWR) — Typical 50 Ohm series, 1.2
max. to 2 GHz.
1,2
— MIL-STD-202, Method
1,2
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
1
— MIL-STD-202, Method
— MIL-STD-202, Method
1
— MIL-STD-
3
3
Materials
Housing, Nut, Inner Sleeve —
Brass per ASTM-B-16, 35% Zinc.
Insulator — TEFLON per
ASTM-D-1710.
Pin & Socket Contacts — Beryllium
Copper per ASTM-B-196.
Middle Sleeve — Copper Alloy.
Facial Seal
Gasket — Silicone Rubber per
ZZ-R-765.
Lockwasher — #425 Bronze Alloy.
Plating
Contacts, Housing, Nut,
Inner Sleeve, Middle Sleeve,
Lockwasher — Gold per MIL-G-45204,
Type II, Grade C, Class 1.
NOTES:
1
2
3
Screw-On Series threaded inter-
face.
Tyco Electronics recommends the
use of wired connectors in vibration
and shock environments. See indi-
vidual specifications for connectors
with wire holes.
VSWR is a system specification.
Where performance is critical,
purchase Tyco Electronics cable
assemblies (See page 127) and
specify VSWR testing and mating
connector part numbers.
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
4
, Sealing Sleeve &