1-1532127-9 Tyco Electronics, 1-1532127-9 Datasheet - Page 52

• Manufacturer Part Number: 1-1532127-9
• Description: Conn Microminiature D SKT 21 POS Solder ST Thru-Hole 21 Terminal 1 Port
• Manufacturer: Tyco Electronics
• Type: Microminiature Dr

Specifications of 1-1532127-9

• Gender: SKT
• Termination Method: Solder
• Mounting: Through Hole
• Body Orientation: Straight

48
Technical and Performance
Data for Metal Shell
Plug (Pin Side)
Shell Type M1
Catalog 1308638
Revised 8-05
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Rectangular Connectors
JACKMATE MCJM Series Metal Shell Center Jackscrew Connectors
Electrical
Contact Resistance — The average
mated contact resistance is 4 milliohms,
with a maximum value of 8 milliohms,
using standard 24 AWG solid copper
leads when measured directly behind the
crimp joints of the mated pin and socket
contacts. The average resistance value at
100 microvolts is 4.8 milliohms.
Dielectric Withstanding Voltage
(60 Hz rms room temperature) —
Solder Pots: 600 VAC at sea level; 150
VAC at 70,000 feet [21,336m].
Wire Terminations: 750 VAC at sea level;
200 VAC at 70,000 feet [21,336m].
Corrosion Resistance (Per MIL-
STD-202C, Method 101B, Condition
B) — Both mated and unmated samples
do not exceed the maximum allowable
contact resistance (8 milliohms) when
subjected to the 48 hour salt spray test.
Durability — The contact resistance
after 500 mating cycles is less than the
maximum allowable, 8 milliohms.
[1.17]
[3.18]
.046
.125
Rad.
Typ.
Rad.
Typ.
[7.62]
.300
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
[5.05]
.199
#10
#48
[1.98]
[4.57]
.078
.180
Insulation Resistance — Greater than
5,000 megohms at room temperature for
the materials listed under “Materials”.
Maximum Current Carrying
Capacity — No. 24 contact 3 amperes.
It must be recognized, however, that all
the wires to a connector will not carry
their maximum current under all envi-
ronmental conditions due to wire tem-
perature.
Mechanical
Contact Engaging & Separation
Forces — 8.0 oz. max. [2.22N] (eng.),
0.5 oz. min.[.14N] (sep.).
Environmental
Temperature Range (Operating) —
-67°F to 302°F [-55°C to 150°C] for
Diallyl Phthalate.
Vibration (Per MIL-STD-202C,
Method 204-A, Condition D) — No
discontinuity in excess of 1 µ sec. dur-
ing twelve 20 minute sweeps from 10 to
2000 CPS at .06 double amplitude or 20
G forces, whichever is less.
[21.08]
.830
Hex
Socket
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
A Polarization
B Polarization
Jackscrew
[4.75]
.187
Jackscrew 2-56 UNC-2B Thd.
[8.89]
.350
#41
#1
Contact Pin
Shell
Insert
Materials
Insulator — Diallyl Phthalate per MIL-
M-14, Type SDG-F.
Contacts — Pin contact: copper alloy
and beryllium copper alloy make up the
complete construction; Socket contact:
copper alloy.
Body Shells — Pin body shell: stain-
less steel, Types 304, Condition A per
QQ-S-766; Socket body shell: aluminum
alloy per QQ-A-591, A-380 alloy.
Hardware — Corrosion resistant
stainless steel.
Finishes
Contacts — Standard finish is
0.000050 [0.00127] gold over copper
flash per MIL-G-45204, Type II.
Body Shells — Pin body shell: passi-
vated per MIL-F-14072 (E-300); Socket
body shell: electroless nickel per AMS
204, Class 3, except thickness is
0.001/0.0015 [0.025/0.038].
Hardware — Passivated per
QQ–P–35.
Note: Insulators are molded into
*Standard material used unless
otherwise specified.
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
their metal shells —
No bonded joint is used.