1-1532127-9 Tyco Electronics, 1-1532127-9 Datasheet - Page 62

• Manufacturer Part Number: 1-1532127-9
• Description: Conn Microminiature D SKT 21 POS Solder ST Thru-Hole 21 Terminal 1 Port
• Manufacturer: Tyco Electronics
• Type: Microminiature Dr

Specifications of 1-1532127-9

• Gender: SKT
• Termination Method: Solder
• Mounting: Through Hole
• Body Orientation: Straight

58
Test Data
MARC 43 Series Connectors meet the applicable performance requirements of specification MIL-C-26482 (Navy) to
include the following selected test parameters listed below:
DESCRIPTION
MIL-C-26482 Test Para
Insulation Resistance,
Room and High Temp.,
Para. 4.7.3
Dielectric Withstanding Voltage,
Para. 4.7.4
Durability,
Para. 4.7.9
Corrosion,
Para. 4.7.10
Sweep Vibration,
Mated, Para. 4.7.11
Moisture Resistance,
Para. 4.7.13 and 4.7.13.1
Contact Retention,
Para. 4.7.16
Contact Arrangements
“A Size” Insert Layouts
(A = ) Shell Size 9
Insert Arrangement
Number of Contacts
Contact Size
“B Size” Insert Layouts
(B = ) Shell Size 12
Insert Arrangement
Number of Contacts
Contact Size
“C Size” Insert Layouts
(C = ) Shell Size 15
Insert Arrangement
Number of Contacts
Contact Size
Catalog 1308638
Revised 8-05
www.tycoelectronics.com
2
2
2
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
1
Circular Connectors
MARC 43 Series Connectors
Notes:
50 Ohm
50 Ohm 22 AWG
50 Ohm 22 AWG
19
-3
12
-1
-9
7
1
2
3
Arrow ( ) indicates insert top or vertical position in relation to top or vertical position of connector housings.
Arrangement also available in hermetic seal receptacles.
Views shown are front face view of receptacles. Front face view of plugs is mirror image of that shown.
TEST REQUIREMENTS
Insulation resistance of unmated connectors shall be 5000 megohms, minimum
at room temperature and 2000 megohms, minimum, at 257°F
when measured per MIL-STD-202, Method 302, Test Condition B.
No evidence of dielectric breakdown or flashover when mated and unmated
plugs are subjected to 1000 volts, rms, per MIL-STD-202, Method 301.
Plugs and receptacles designed to withstand up to 500 cycles of engagement
and separation without detrimental electrical or mechanical damage to the
connectors.
Unmated plugs and receptacles shall show no exposure of basis metal due
to corrosion which would affect electrical or mechanical performance of the
connectors after subjection to 24 hours exposure to salt spray atmosphere
per MIL-STD 202, Method 101.
Mated connectors shall show no circuit interruptions greater than 10 micro-
seconds during 12 hours vibration to include six sweeps in two axes at
-67°F [-55°C], room temperature, and 257°F [+125°C] per MIL-STD-202, Method
204, Test Condition B. Post inspection shall show no detrimental cracking,
breaking, or loosening of parts.
The insulation resistance of mated connectors shall exceed 100 megohms
after subjection to moisture resistance testing per MIL-STD-202, Method 106.
Contacts shall withstand 15 lbs [66.7 N] axial load without axial displacement in
excess of 0.012 [0.305] or damage to contacts or inserts when the axial load is
applied to the mating end of the contacts in unmated plugs and receptacles
at a rate of approximately 1 lb/sec.
-10
19
-2
37
22 AWG
3
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
61
-4
2-22 AWG
2-50 Ohm
13-22 AWG
6-50 Ohm
-5
-15
(Continued)
22-22 AWG
2-75 Ohm
16 AWG 22 AWG
-7
16 AWG
-11
7
-19
12
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
-12
12
95 Ohm 6-12 AWG
43-22 AWG
-34
2-50 Ohm
5
-13
7-22 AWG
2-50 Ohm
13-22 AWG
-14
-37
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
5-75 Ohm
4-95 Ohm
16 AWG
-27
-17
4
75 Ohm
[
+125°C]
-47
5
6-16 AWG
1-50 Ohm
29-22 AWG
-21
2-16 AWG
75 Ohm
-48
-49
12