XR16L2450IJ-F Exar Corporation, XR16L2450IJ-F Datasheet - Page 19

• Manufacturer Part Number: XR16L2450IJ-F
• Description: 2.25 To 5.5V W/ 5V TOLERANT DUART
• Manufacturer: Exar Corporation

Specifications of XR16L2450IJ-F

• Features: *
• Number Of Channels: 2, DUART
• Fifo's: 1 Byte
• Protocol: RS232
• Voltage - Supply: 2.25 V ~ 5.5 V
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• With Cmos: Yes
• Mounting Type: Surface Mount
• Package / Case: 44-LCC (J-Lead)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

xr
REV. 1.1.1
MSR[1]: Delta DSR# Input Flag
•
•
MSR[2]: Delta RI# Input Flag
•
•
MSR[3]: Delta CD# Input Flag
•
•
MSR[4]: CTS Input Status
Normally this bit is the compliment of the CTS# input. However in the loopback mode, this bit is equivalent to
the RTS# bit in the MCR register. The CTS# input may be used as a general purpose input when the modem
interface is not used.
MSR[5]: DSR Input Status
Normally this bit is the compliment of the DSR# input. In the loopback mode, this bit is equivalent to the DTR#
bit in the MCR register. The DSR# input may be used as a general purpose input when the modem interface is
not used.
MSR[6]: RI Input Status
Normally this bit is the compliment of the RI# input. In the loopback mode this bit is equivalent to bit-2 in the
MCR register. The RI# input may be used as a general purpose input when the modem interface is not used.
MSR[7]: CD Input Status
Normally this bit is the compliment of the CD# input. In the loopback mode this bit is equivalent to bit-3 in the
MCR register. The CD# input may be used as a general purpose input when the modem interface is not used.
This is a 8-bit general purpose register for the user to store temporary data. The content of this register is
preserved during sleep mode but becomes 0xFF (default) after a reset or a power off-on cycle.
The Baud Rate Generator (BRG) is a 16-bit counter that generates the data rate for the transmitter. The rate is
programmed through registers DLL and DLM which are only accessible when LCR bit-7 is set to ‘1’.
“Programmable Baud Rate Generator” on page 8.
This register contains the device ID (0x02 for XR16L2450). Prior to reading this register, DLL and DLM should
be set to 0x00.
This register contains the device revision information. For example, 0x01 means revision A. Prior to reading
this register, DLL and DLM should be set to 0x00.
4.9
4.10
4.11
4.12
Logic 0 = No change on DSR# input (default).
Logic 1 = The DSR# input has changed state since the last time it was monitored. A modem status interrupt
will be generated if MSR interrupt is enabled (IER bit-3).
Logic 0 = No change on RI# input (default).
Logic 1 = The RI# input has changed from a logic 0 to a logic 1, ending of the ringing signal. A modem status
interrupt will be generated if MSR interrupt is enabled (IER bit-3).
Logic 0 = No change on CD# input (default).
Logic 1 = Indicates that the CD# input has changed state since the last time it was monitored. A modem
status interrupt will be generated if MSR interrupt is enabled (IER bit-3).
Scratch Pad Register (SPR) - Read/Write
Baud Rate Generator Registers (DLL and DLM) - Read/Write
Device Identification Register (DVID) - Read Only
Device Revision Register (DREV) - Read Only
for more details.
19
2.25V TO 5.5V DUART
XR16L2450
See