171662-1 TE Connectivity, 171662-1 Datasheet - Page 7

• Manufacturer Part Number: 171662-1
• Description: E-J MK-2 070 REC CONT
• Manufacturer: TE Connectivity
• Type: Contactr
• Series: 070r

Specifications of 171662-1

• Gender: RCP
• Body Orientation: Straight
• Housing Material: Not Required
• Number Of Contacts: 1POS
• Number Of Ports: 1Port
• Number Of Terminals: 1
• Pitch (mm): Not Requiredmm
• Contact Material: Brass
• Operating Temp Range: -30C to 105C
• Mounting Style: Cable
• Termination Method: Crimp
• Contact Plating: Pre-Tin
• Product Height (mm): 3.6mm
• Product Depth (mm): 5.4mm
• Product Length (mm): 16.5mm
• Product Line: Econoseal J
• Product Type: Contact
• Wire/cable Type: Discrete Wire
• Cable Type: Thin Wall
• Termination Method To Wire/cable: Crimp
• Wire/cable Size (awg): 16 – 20
• Wire/cable Size (mm²): 0.5 – 1.25
• Wire Type: Stranded
• Contact Type: Socket
• Contact Base Material: Brass
• Contact Plating, Mating Area, Material: Pre-Tin
• Contact Plating, Mating Area, Thickness (µm [?in]): 0.76 [29.92]
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Not relevant for lead free process
• Rohs/elv Compliance History: Always was RoHS compliant
• Applies To: Wire/Cable
• Accepts Wire Insulation Diameter, Range (mm [in]): 2.00 – 2.60 [0.079 – 0.102]
• Application Use: Wire-to-Wire
• Contact Transmits (typical Application): Power
• Packaging Method: Reel
• Packaging Quantity: 6000
• Lead Free Status / RoHS Status: Compliant

AMP Sealed Connectors
A
Contacts
Wire Seals and Cavity Plugs
Connector Housings
070 series tab contacts.
1.8 mm [.071 in.] wide x
0.64 mm [.025 in.] thick
Receptacle contacts are
available in brass or
phosphor bronze with pre-
tin or gold plating.
Tab contacts are available
in pre-tin or gold plated
brass.
Lanceless design to reduce
tangling.
Wire range 0.20 - 1.25
mm
Made from NBR material.
Wire seal and contact
crimped simultaneously.
For wire insulation
diameters of 1.4 - 2.6 mm
[.055 - .102 in.]
Housings and lock plates
made from PBT material.
Connectors available in 1,
2, 3, 4, 6, 8, 10, and 12
position versions.
Utilize a loose piece
secondary lock (sold
separately).
Cavity plugs are available
to seal unused contact
cavities.
An audible click helps
insure proper connector
mating.
Protected locking lever.
Recognized under the
Component
Program of
Underwriters
Laboratories Inc.
File No. E28476.
2
[#24 - #16 AWG]
AMP Technical Support Center/AMP FAX Service
1-800-522-6752 717-986-7777
AMP Sealed Connectors
Econoseal J Series [Mark II(+)] . . . Sealed Connectors
AMP Econoseal J Series
Mark II
been developed for use in
automobile engine
compartments and other
applications where
waterproof protection and
rugged construction are
required.
Waterproof protection is
achieved by means of a
wire seal which is inserted
onto the wire and crimped
simultaneously with the
insulation support of the
contact. Plug housings
include a factory installed
NBR interface seal. Cavity
plugs are available to seal
contact positions on the
connector which are not
used.
The wire seals and cavity
plugs incorporate a
beveled, 3 ridge design,
with the front two ridges
being slightly smaller than
the rear ridge to reduce
(+)
Connectors have
insertion into the connector
housing. Another important
feature allows trapped air to
escape when the internal
connector pressure
becomes excessive due to
changes in temperature or
atmospheric pressure.
The MarkII
incorporates a secondary
lock plate which when
inserted into the connector
housing will detect partially
mated contacts. The lock
plate also increases contact
retention and prevents
contact damage during
mating or unmating of the
connector.
required for each connector
housing. Lock plates are
sold separately.
Sealing surfaces of the
MarkII
located inside of the
connector housing thus
reducing the possibility of
damage to the seal during
handling.
Dimensions are in
millimeters over [inches]
(+)
connector are
(+)
One lock plate is
connector
www.amp.com
Product Performance
Temperature Rating
-30 to 105 o C (including temperature
rise due to applied current.)
Contact Termination Resistance
3 m (Max. (Initial)
10 m (Max. (Final)
Dielectric Strength
1.0 kVAC between adjacent contacts.
Current Guidelines
See page 13 of the product specification
for information.
Product Documentation
Product Specification
108-5262
Application Specification
114-5082
Customer Manual
CM-325J
Sample Kit
889458
Specifications
subject to change.
Revised 01-00
Catalog
65481
7