ISL12028IBZ Intersil, ISL12028IBZ Datasheet - Page 22

• Manufacturer Part Number: ISL12028IBZ
• Description: IC RTC W/EEPROM 14-SOIC
• Manufacturer: Intersil
• Type: Clock/Calendar/Supervisor/EEPROMr

Specifications of ISL12028IBZ

• Memory Size: 4K (512 x 8)
• Time Format: HH:MM:SS (12/24 hr)
• Date Format: YY-MM-DD-dd
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 14-SOIC (3.9mm Width), 14-SOL
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Application Section
Crystal Oscillator and Temperature Compensation
Intersil has now integrated the oscillator compensation
circuity on-chip, to eliminate the need for external
components and adjust for crystal drift over-temperature and
enable very high accuracy time keeping (<5ppm drift).
The Intersil RTC family uses an oscillator circuit with on-chip
crystal compensation network, including adjustable
load-capacitance. The only external component required is
the crystal. The compensation network is optimized for
operation with certain crystal parameters which are common
in many of the surface mount or tuning-fork crystals available
today. Table 9 summarizes these parameters.
Table 10 contains some crystal manufacturers and part
numbers that meet the requirements for the Intersil RTC
products.
The turnover-temperature in Table 9 describes the
temperature where the apex of the of the drift vs temperature
curve occurs. This curve is parabolic with the drift increasing
as (T-T0)
turnover-temperature is typically +25°C, and a peak drift of
2
. For an Epson MC-405 device, for example, the
SIGNALS FROM
SIGNALS FROM
SIGNALS FROM
THE MASTER
SIGNALS FROM
SDA BUS
THE SLAVE
THE MASTER
SDA BUS
THE SLAVE
22
S
A
R
T
T
1
ADDRESS
ADDRESS
SLAVE
FIGURE 25. RANDOM ADDRESS READ SEQUENCE
SLAVE
1
1
A
C
K
FIGURE 26. SEQUENTIAL READ SEQUENCE
1
1
0
A
C
K
ISL12028, ISL12028A
0 0 0 0 0 0 0
DATA
ADDRESS 1
(1)
WORD
A
C
K
A
C
K
ADDRESS 0
>110ppm occurs at the temperature extremes of -40 and
+85°C. It is possible to address this variable drift by adjusting
the load capacitance of the crystal, which will result in
predictable change to the crystal frequency. The Intersil RTC
family allows this adjustment over-temperature since the
devices include on-chip load capacitor trimming. This control
is handled by the Analog Trimming Register, or ATR, which
has 6-bits of control. The load capacitance range covered by
the ATR circuit is approximately 3.25pF to 18.75pF, in
0.25pF increments. Note that actual capacitance would also
include about 2pF of package related capacitance. In-circuit
tests with commercially available crystals demonstrate that
this range of capacitance allows frequency control from
+116ppm to -37ppm, using a 12.5pF load crystal.
In addition to the analog compensation afforded by the
adjustable load capacitance, a digital compensation feature
is available for the Intersil RTC family. There are three bits
known as the Digital Trimming Register or DTR, and they
operate by adding or skipping pulses in the clock signal. The
range provided is ±30ppm in increments of 10ppm. The
default setting is 0ppm. The DTR control can be used for
coarse adjustments of frequency drift over-temperature or
for crystal initial accuracy correction.
DATA
(2)
WORD
A
C
K
A
C
K
S
T
A
R
T
(n IS ANY INTEGER GREATER THAN 1)
1
ADDRESS
(n - 1)
DATA
SLAVE
1
1
1
1
A
C
K
A
C
K
DATA
DATA
(n)
S
O
P
T
November 30, 2010
O
S
T
P
FN8233.9