ISL22316UFRT10Z-TK Intersil, ISL22316UFRT10Z-TK Datasheet - Page 4

• Manufacturer Part Number: ISL22316UFRT10Z-TK
• Description: IC POT DGTL 128TP LN LP 10-TDFN
• Manufacturer: Intersil
• Series: XDCP™r

Specifications of ISL22316UFRT10Z-TK

• Taps: 128
• Resistance (ohms): 50K
• Number Of Circuits: 1
• Temperature Coefficient: 80 ppm/°C Typical
• Memory Type: Non-Volatile
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 10-TDFN Exposed Pad
• Resistance In Ohms: 50K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ISL22316UFRT10Z-TK

Analog Specifications
Operating Specifications
RESISTOR MODE (Measurements between R
V
SYMBOL
(Note 18)
(Note 18)
t
ShdnRec
CC
I
SYMBOL
(Note 15)
(Note 14)
(Note 13)
LkgDig
I
I
t
Vpor
Roffset
DCP
CC1
CC2
I
I
RDNL
SB
SD
t
RINL
Ramp V
D
V
V
V
V
Leakage Current, at Pins A0, A1, SHDN,
SDA and SCL
DCP Wiper Response Time
DCP Recall Time from Shutdown Mode
Power-on Recall Voltage
Power-up Delay
CC
CC
CC
CC
CC
Integral Non-linearity
Differential Non-linearity
Offset
Supply Current (Non-volatile Write/Read) f
Supply Current (Volatile Write/Read)
Current (Standby)
Current (Shutdown)
Ramp Rate
PARAMETER
PARAMETER
Over recommended operating conditions, unless otherwise stated. (Continued)
4
Over the recommended operating conditions, unless otherwise specified.
W
and R
L
DCP register set between 10 hex and 7F
hex; monotonic over all tap positions;
W and U option
W option
U option
W option
U option
with R
f
active, read and write states)
active, read and write states)
V
standby state
V
standby state
V
standby state
V
standby state
V
standby state
V
standby state
V
standby state
V
standby state
Voltage at pin from GND to V
SDA is inactive
SCL falling edge of last bit of DCP data byte
to wiper new position
From rising edge of SHDN signal to wiper
stored position and RH connection
SCL falling edge of last bit of ACR data byte
to wiper stored position and RH connection
Minimum V
V
Register recall completed and I
in standby state
SCL
SCL
CC
CC
CC
CC
CC
CC
CC
CC
CC
H
= +5.5V @ +85°C, I
= +5.5V @ +125°C, I
= +3.6V @ +85°C, I
= +3.6V @ +125°C, I
= +5.5V @ +85°C, I
= +5.5V @ +125°C, I
= +3.6V @ +85°C, I
= +3.6V @ +125°C, I
above Vpor, to DCP Initial Value
= 400kHz; SDA = Open; (for I
= 400kHz; SDA = Open; (for I
not connected, or between R
ISL22316
TEST CONDITIONS
CC
TEST CONDITIONS
at which memory recall occurs
2
2
2
2
C interface in
C interface in
C interface in
C interface in
2
2
2
2
C interface in
C interface in
C interface in
C interface in
CC,
2
C Interface
2
2
W
C,
C,
and R
(Note 19)
H
(Note 19)
MIN
-0.5
with R
-1
-1
0
0
MIN
2.0
0.2
-1
L
not connected)
(Note 5)
(Note 5)
TYP
0.5
1
TYP
1.5
1.5
1.5
(Note 19)
(Note 19)
MAX
0.5
MAX
1
1
5
2
0.5
2.6
September 1, 2009
3
5
7
3
5
3
5
2
4
1
3
(Note 12)
(Note 12)
(Note 12)
(Note 12)
(Note 12)
FN6186.2
UNIT
UNIT
V/ms
MI
MI
MI
MI
MI
mA
mA
ms
µA
µA
µA
µA
µA
µA
µA
µA
µA
µs
µs
µs
V