AD5173BRM2.5-RL7 Analog Devices Inc, AD5173BRM2.5-RL7 Datasheet - Page 19

• Manufacturer Part Number: AD5173BRM2.5-RL7
• Description: IC DGTL POT DUAL 2.5K OTP 10MSOP
• Manufacturer: Analog Devices Inc

Specifications of AD5173BRM2.5-RL7

• Rohs Status: RoHS non-compliant
• Taps: 256
• Resistance (ohms): 2.5K
• Number Of Circuits: 2
• Temperature Coefficient: 35 ppm/°C Typical
• Memory Type: Non-Volatile
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 10-MSOP, Micro10™, 10-uMAX, 10-uSOP
• Resistance In Ohms: 2.5K
• Number Of Elements: 2
• # Of Taps: 256
• Resistance (max): 2.5KOhm
• Power Supply Requirement: Single
• Interface Type: Serial (2-Wire/I2C)
• Single Supply Voltage (typ): 3/5V
• Dual Supply Voltage (typ): Not RequiredV
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 10
• Lead Free Status / RoHS Status: Not Compliant

I
WRITE MODE
Table 10. AD5172 Write Mode
Table 11. AD5173 Write Mode
READ MODE
Table 12. AD5172 Read Mode
Table 13. AD5173 Read Mode
Table 14. SDA Bits Descriptions
Bit
S
P
A
AD0, AD1
X
W
R
A0
SD
T
OW
D7, D6, D5, D4, D3, D2, D1, D0
E1, E0
2
S
S
S
S
C INTERFACE
0
0
0
0
1
1
1
1
Slave address byte
Slave address byte
Slave address byte
Slave address byte
0
0
0
0
1
1
1
1
1 AD1 AD0 W
1 AD1 AD0 R
1
1
1
1
1
1
W
Description
Start condition.
Stop condition.
Acknowledge.
Package pin-programmable address bits.
Don’t care.
Write.
Read.
RDAC subaddress select bit.
Shutdown connects wiper to B terminal and open circuits the A terminal. It does not change the
contents of the wiper register.
OTP programming bit. Logic 1 programs the wiper permanently.
Overwrites the fuse setting and programs the digital potentiometer to a different setting. Upon
power-up, the digital potentiometer is preset to either midscale or fuse setting, depending on
whether the fuse link was blown.
Data bits.
OTP validation bits.
00 = ready to program.
10 = fatal error. Some fuses not blown. Do not retry. Discard this unit.
11 = programmed successfully. No further adjustments are possible.
R
A
A D7 D6 D5 D4 D3 D2 D1 D0 A
A A0 SD
A D7 D6 D5 D4 D3 D2 D1 D0 A
A0 SD
Instruction byte
Instruction byte
T
Instruction byte
Instruction byte
T
Rev. H | Page 19 of 24
0 OW X
0 OW X
X
X
X
X
A
A D7 D6 D5 D4 D3 D2 D1 D0
D7 D6 D5 D4 D3 D2 D1 D0
E1 E0
E1 E0
X
X
Data byte
Data byte
Data byte
Data byte
X
X
X
X
AD5172/AD5173
X
X
X
X
X
X
A
A
A
A
P
P
P
P