AD5173BRM2.5-RL7 Analog Devices Inc, AD5173BRM2.5-RL7 Datasheet - Page 22

• Manufacturer Part Number: AD5173BRM2.5-RL7
• Description: IC DGTL POT DUAL 2.5K OTP 10MSOP
• Manufacturer: Analog Devices Inc

Specifications of AD5173BRM2.5-RL7

• Rohs Status: RoHS non-compliant
• Taps: 256
• Resistance (ohms): 2.5K
• Number Of Circuits: 2
• Temperature Coefficient: 35 ppm/°C Typical
• Memory Type: Non-Volatile
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 10-MSOP, Micro10™, 10-uMAX, 10-uSOP
• Resistance In Ohms: 2.5K
• Number Of Elements: 2
• # Of Taps: 256
• Resistance (max): 2.5KOhm
• Power Supply Requirement: Single
• Interface Type: Serial (2-Wire/I2C)
• Single Supply Voltage (typ): 3/5V
• Dual Supply Voltage (typ): Not RequiredV
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 10
• Lead Free Status / RoHS Status: Not Compliant

AD5172/AD5173
Multiple Devices on One Bus (AD5173 Only)
Figure 52 shows four AD5173 devices on the same serial bus.
Each has a different slave address because the states of the AD0
and AD1 pins are different. This allows each device on the bus to
be written to or read from independently. The master device
output bus line drivers are open-drain pull-downs in a fully
I
MASTER
2
C-compatible interface.
SDA
AD5173
AD1
AD0
Figure 52. Multiple AD5173 Devices on One I
R
SCL
P
R
P
5V
SDA
AD5173
AD1
AD0
SCL
5V
5V
SDA
AD5173
AD1
AD0
SCL
2
5V
C Bus
SDA
AD5173
AD1
AD0
SCL
Rev. H | Page 22 of 24
SDA
SCL
LEVEL SHIFTING FOR DIFFERENT VOLTAGE
OPERATION
If the SCL and SDA signals come from a low voltage logic
controller and are below the minimum V
level shift the signals for read/write communications between
the AD5172/AD5173 and the controller. Figure 53 shows one
of the implementations. For example, when SDA1 is at 2.5 V,
M1 turns off, and SDA2 becomes 5 V. When SDA1 is at 0 V,
M1 turns on, and SDA2 approaches 0 V. As a result, proper
level shifting is established. It is best practice for M1 and M2
to be low threshold N-channel power MOSFETs, such as the
FDV301N from Fairchild Semiconductor.
SDA1
SCL1
V
DD1
CONTROLLER
= 2.5V
Figure 53. Level Shifting for Different Voltage Operation
2.5V
R
P
R
P
S
M1
G
D
S
M2
G
D
R
P
IH
level (0.7 V × V
2.7V TO 5.5V
AD5172/
AD5173
R
P
V
DD2
= 5V
SDA2
SCL2
DD
),