ISL95810UIRT8Z Intersil, ISL95810UIRT8Z Datasheet
ISL95810UIRT8Z
Specifications of ISL95810UIRT8Z
Related parts for ISL95810UIRT8Z
ISL95810UIRT8Z Summary of contents
Page 1
... ISL95810UIU8Z* AOK (Note) ISL95810UIRT8 AIT ISL95810UIRT8Z* APP (Note) *Add “-T” suffix for tape and reel. NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations ...
Page 2
Block Diagram SDA SCL WP Pin Descriptions TSSOP PIN SYMBOL SCL 3 SDA 4 GND ISL95810 VCC WIPER REGISTER AND CONTROL NON-VOLATILE REGISTER GND ...
Page 3
Absolute Maximum Ratings Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Voltage at Any Digital Interface Pin with Respect to ...
Page 4
Operating Specifications Over the recommended operating conditions unless otherwise specified. (Continued) SYMBOL PARAMETER I Leakage Current, at Pins SDA, SCL, LkgDig and WP Pins t (Note 13) DCP Wiper Response Time DCP Vpor Power-On Recall Voltage V Ramp V Ramp ...
Page 5
Operating Specifications Over the recommended operating conditions unless otherwise specified. (Continued) SYMBOL PARAMETER Rpu (Note 13) SDA and SCL Bus Pull-Up Resistor Off-Chip t (Notes 13, 14) Non-Volatile Write Cycle Time Setup Time SU: Hold ...
Page 6
Typical Performance Curves 160 85°C CC 140 -40°C CC 120 100 5. -40° 5. 25° ...
Page 7
Typical Performance Curves 0 25°C CC 0 85° -40° 132 TAP POSITION (DECIMAL) FIGURE 7. DNL ...
Page 8
Typical Performance Curves Signal at Wiper (Wiper Unloaded) Wiper Movement Mid Point From 80h to 7fh FIGURE 13. MIDSCALE GLITCH, CODE 80h to 7Fh (WIPER 0) Principles of Operation The ISL95810 is an integrated circuit incorporating one DCP with its ...
Page 9
The ISL95810 is pre-programed with 80h in the IVR. TABLE 1. MEMORY MAP ADDRESS NON-VOLATILE Reserved 0 IVR WR: Wiper Register, IVR: Initial value Register Serial Interface The ISL95810 supports a bidirectional bus oriented ...
Page 10
SCL FROM MASTER SDA OUTPUT FROM TRANSMITTER SDA OUTPUT FROM RECEIVER START FIGURE 16. ACKNOWLEDGE RESPONSE FROM RECEIVER SIGNALS FROM THE MASTER SIGNAL AT SDA SIGNALS FROM THE ISL95810 S SIGNALS T FROM THE A IDENTIFICATION MASTER R BYTE WITH ...
Page 11
If the Address Byte the Data Byte is transferred to the Wiper Register (WR the Access Control Register respectively, at the falling edge of the SCL pulse that loads the last bit (LSB) ...
Page 12
Mini Small Outline Plastic Packages (MSOP -B- INDEX 1 2 0.20 (0.008) AREA TOP VIEW 0.25 (0.010) GAUGE PLANE SEATING PLANE - 0.10 (0.004) b -H- - 0.20 (0.008) SIDE VIEW 0.20 ...
Page 13
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...