X9401WS24IZ-2.7T1 Intersil, X9401WS24IZ-2.7T1 Datasheet
X9401WS24IZ-2.7T1
Specifications of X9401WS24IZ-2.7T1
Available stocks
Related parts for X9401WS24IZ-2.7T1
X9401WS24IZ-2.7T1 Summary of contents
Page 1
... CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. | 1-888-INTERSIL or 1-888-468-3774 Intersil (and design registered trademark of Intersil Americas Inc. XDCP is a trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2005-2006, 2009. All Rights Reserved All other trademarks mentioned are the property of their respective owners. X9401 Low Noise/Low Power/SPI Bus FN8190 ...
Page 2
... Ordering Information PART PART NUMBER MARKING X9401WS24IZ* (Note 1) X9401WS ZI X9401WS24I X9401WS I X9401WS24Z* (Note 1) X9401WS Z X9401WV24IZ* (Note 1) X9401WV ZI X9401WV24Z* (Note 1) X9401WV Z X9401WS24I-2.7* (Note 2) X9401WS G X9401WS24IZ-2.7* (Note) X9401WS ZG X9401WS24Z-2.7* (Note 1) X9401WS ZF X9401WV24-2.7 X9401WV F X9401WV24IZ-2.7* (Note 1) X9401WV ZG X9401WV24Z-2.7* (Note 1) X9401WV ZF *Add “T1” suffix for tape and reel. Please refer to TB347 for details on reel specifications. ...
Page 3
Pinouts X9401 (24 LD SOIC) TOP VIEW ...
Page 4
Data Registers Each potentiometer has four 6-bit nonvolatile data registers. These can be read or written directly by the host. Data can also be transferred between any of the four data registers and the associated Wiper Counter Register. All operations ...
Page 5
Wiper Counter Register. These instructions are: • Read Wiper Counter Register: read the current wiper position of the selected pot, • Write Wiper Counter Register: change current wiper position of the selected pot, ...
Page 6
CS SCK SCL FIGURE 4. THREE-BYTE COMMAND SEQUENCE (WRITE) CS SCL FIGURE 5. THREE-BYTE COMMAND SEQUENCE (READ) ...
Page 7
SCK INC/DEC CMD ISSUED INSTRUCTION I 3 Read Wiper Counter Register 1 Write Wiper Counter Register 1 Read Data Register 1 Write Data Register 1 XFR Data Register to Wiper 1 Counter Register XFR Wiper ...
Page 8
Instruction Format NOTES A0”: stands for the device addresses sent by the master. 4. WPx refers to wiper position data in the Counter Register 5. “I”: stands for the increment operation, SI held HIGH during active SCK ...
Page 9
Global Transfer Wiper Counter Register (WCR) to Data Register (DR) DEVICE TYPE DEVICE CS IDENTIFIER ADDRESSES FALLING EDGE Read Status DEVICE TYPE DEVICE CS IDENTIFIER ADDRESSES FALLING EDGE ...
Page 10
... CC 10 X9401 Thermal Information Temperature Under Bias . . . . . . . . . . . . . . . . . . . . .-65°C to +135°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Pb-Free Reflow Profile .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Operating Conditions Temperature Range Commercial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C Industrial .-40°C to +85°C TEST CONDITION +25°C, each pot I ...
Page 11
DC Operating Characteristics (Over the recommended operating conditions unless otherwise specified.) SYMBOL PARAMETER I V Supply Current (active) CC1 Supply Current (non-volatile write) CC2 Current (standby Input Leakage Current LI I ...
Page 12
AC Timing SYMBOL f SSI/SPI clock frequency SCK t SSI/SPI clock cycle rime CYC t SSI/SPI clock high rime WH t SSI/SPI clock low time WL t Lead time LEAD t Lag time LAG t SI, SCK, HOLD and CS ...
Page 13
Symbol Table WAVEFORM INPUTS OUTPUTS MUST BE WILL BE STEADY STEADY MAY CHANGE WILL CHANGE FROM FROM HIGH HIGH MAY CHANGE WILL CHANGE FROM HIGH TO FROM HIGH TO LOW LOW DON’T CARE: CHANGING: ...
Page 14
Hold Timing CS SCK HOLD XDCP Timing (for All Load Instructions) CS SCK MSB HIGH IMPEDANCE SO XDCP Timing (for Increment/Decrement Instruction) CS SCK ADDR SI HIGH ...
Page 15
Applications information Basic Configurations of Electronic Potentiometers V R THREE TERMINAL POTENTIOMETER; VARIABLE VOLTAGE DIVIDER Application Circuits NONINVERTING AMPLIFIER – (1 OFFSET VOLTAGE ADJUSTMENT ...
Page 16
Application Circuits (continued) INVERTING AMPLIFIER – – X9401 EQUIVALENT L-R CIRCUIT ...
Page 17
Small Outline Plastic Packages (SOIC) N INDEX 0.25(0.010) H AREA E - SEATING PLANE - -C- α 0.10(0.004) 0.25(0.010 NOTES: 1. Symbols are defined in the ...
Page 18
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...