AD9754ARU Analog Devices Inc, AD9754ARU Datasheet - Page 18

• Manufacturer Part Number: AD9754ARU
• Description: IC DAC 14BIT 125MSPS 28-TSSOP
• Manufacturer: Analog Devices Inc
• Series: TxDAC®r

Specifications of AD9754ARU

• Mounting Type: Surface Mount
• Rohs Status: RoHS non-compliant
• Settling Time: 35ns
• Number Of Bits: 14
• Data Interface: Parallel
• Number Of Converters: 1
• Voltage Supply Source: Analog and Digital
• Power Dissipation (max): 220mW
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-TSSOP
• Resolution (bits): 14bit
• No. Of Pins: 28
• Update Rate: 125MSPS
• Peak Reflow Compatible (260 C): No
• No. Of Bits: 14 Bit
• Leaded Process Compatible: No
• Voltage Rating: 5V
• Number Of Channels: 1
• Resolution: 14b
• Interface Type: Parallel
• Single Supply Voltage (typ): 5V
• Dual Supply Voltage (typ): Not RequiredV
• Power Supply Requirement: Analog and Digital
• Output Type: Current
• Single Supply Voltage (min): 4.5V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 28
• Lead Free Status / Rohs Status: Not Compliant

AD9754
APPLICATIONS
VDSL Applications Using the AD9754
Very High Frequency Digital Subscriber Line (VDSL) technol-
ogy is growing rapidly in applications requiring data transfer
over relatively short distances. By using QAM modulation and
transmitting the data in multiple discrete tones, high data rates
can be achieved.
As with other multitone applications, each VDSL tone is ca-
pable of transmitting a given number of bits, depending on the
signal to noise ratio (SNR) in a narrow band around that tone.
The tones are evenly spaced over the range of several kHz to
10 MHz. At the high frequency end of this range, performance
is generally limited by cable characteristics and environmental
factors, such as external interferers. Performance at the lower
frequencies is much more dependent on the performance of the
components in the signal chain. In addition to in-band noise,
intermodulation from other tones can also potentially interfere
with the recovery of data for a given tone. The two graphs in
Figure 35 represent a 500 tone missing bin test vector, with
frequencies evenly spaced from 400 Hz to 10 MHz. This test is
very commonly done to determine if distortion will limit the
number of bits which can transmitted in a tone. The test vector
has a series of missing tones around 750 kHz, which is represented
in Figure 35a, and a series of missing tones around 5 MHz,
which is represented in Figure 35b. In both cases, the spurious
free range between the transmitted tones and the empty bins is
greater than 60 dB.
Figure 35a. Notch in missing bin at 750 kHz is down
>60 dB. Peak amplitude = 0 dBm.
–100
–110
–30
–40
–50
–60
–70
–80
–90
600k
FREQUENCY – Hz
800k
1.0M
–18–
CDMA
Carrier Division Multiple Access, or CDMA, is an air transmit/
receive scheme where the signal in the transmit path is modu-
lated with a pseudorandom digital code (sometimes referred to
as the spreading code). The effect of this is to spread the trans-
mitted signal across a wide spectrum. Similar to a DMT wave-
form, a CDMA waveform containing multiple subscribers can
be characterized as having a high peak to average ratio (i.e.,
crest factor), thus demanding highly linear components in the
transmit signal path. The bandwidth of the spectrum is defined
by the CDMA standard being used, and in operation is imple-
mented by using a spreading code with particular characteristics.
Distortion in the transmit path can lead to power being trans-
mitted out of the defined band. The ratio of power transmitted
in-band to out-of-band is often referred to as Adjacent Channel
Power (ACP). This is a regulatory issue due to the possibility of
interference with other signals being transmitted by air. Regula-
tory bodies define a spectral mask outside of the transmit band,
and the ACP must fall under this mask. If distortion in the
transmit path cause the ACP to be above the spectral mask,
then filtering, or different component selection is needed to
meet the mask requirements.
Figure 36 shows an example of the AD9754 used in a W-CDMA
transmitter application using the AD6122 CDMA 3 V transmit-
ter IF subsystem. The AD6122 has functions, such as external
gain control and low distortion characteristics, needed for the
superior Adjacent Channel Power (ACP) requirements of
WCDMA.
Figure 35b. Notch in missing bin at 5 MHz is down
>60 dB. Peak amplitude = 0 dBm.
–100
–110
–30
–40
–50
–60
–70
–80
–90
4.8
FREQUENCY – MHz
5.0
5.2
REV. A