ADSP-2181BST-133 Analog Devices Inc, ADSP-2181BST-133 Datasheet - Page 13

• Manufacturer Part Number: ADSP-2181BST-133
• Description: IC DSP CONTROLLER 16BIT 128TQFP
• Manufacturer: Analog Devices Inc
• Series: ADSP-21xxr
• Type: Fixed Pointr

Specifications of ADSP-2181BST-133

• Rohs Status: RoHS non-compliant
• Interface: Synchronous Serial Port (SSP)
• Clock Rate: 33.3MHz
• Non-volatile Memory: External
• On-chip Ram: 80kB
• Voltage - I/o: 5.00V
• Voltage - Core: 5.00V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 128-TQFP, 128-VQFP
• Device Core Size: 16b
• Architecture: Enhanced Harvard
• Format: Fixed Point
• Clock Freq (max): 33.3MHz
• Mips: 33.3
• Device Input Clock Speed: 33.3MHz
• Ram Size: 80KB
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (min): 4.5V
• Operating Supply Voltage (max): 5.5V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 128
• Package Type: TQFP
• Lead Free Status / RoHS Status: Not Compliant

ABSOLUTE MAXIMUM RATINGS
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
Input Voltage . . . . . . . . . . . . . . . . . . . . . –0.3 V to V
Output Voltage Swing . . . . . . . . . . . . . . –0.3 V to V
Operating Temperature Range (Ambient) . . . . –40 C to +85 C
Storage Temperature Range . . . . . . . . . . . . . –65 C to +150 C
Lead Temperature (5 sec) TQFP . . . . . . . . . . . . . . . . +280 C
Lead Temperature (5 sec) PQFP . . . . . . . . . . . . . . . . . +280 C
*Stresses above those listed under Absolute Maximum Ratings may cause perma-
TIMING PARAMETERS
GENERAL NOTES
Use the exact timing information given. Do not attempt to
derive parameters from the addition or subtraction of others.
While addition or subtraction would yield meaningful results for
an individual device, the values given in this data sheet reflect
statistical variations and worst cases. Consequently, you cannot
meaningfully add up parameters to derive longer times.
TIMING NOTES
Switching Characteristics specify how the processor changes its
signals. You have no control over this timing—circuitry external
to the processor must be designed for compatibility with these
signal characteristics. Switching characteristics tell you what the
processor will do in a given circumstance. You can also use switch-
ing characteristics to ensure that any timing requirement of a
device connected to the processor (such as memory) is satisfied.
Timing Requirements apply to signals that are controlled by cir-
cuitry external to the processor, such as the data input for a read
operation. Timing requirements guarantee that the processor
operates correctly with other devices.
REV. D
ESD SENSITIVITY
The ADSP-2181 is an ESD (electrostatic discharge) sensitive device. Electrostatic charges readily
accumulate on the human body and equipment and can discharge without detection. Permanent
damage may occur to devices subjected to high energy electrostatic discharges.
The ADSP-2181 features proprietary ESD protection circuitry to dissipate high energy discharges
(Human Body Model). Per method 3015 of MIL-STD-883, the ADSP-2181 has been classified as
a Class 1 device.
Proper ESD precautions are recommended to avoid performance degradation or loss of function-
ality. Unused devices must be stored in conductive foam or shunts, and the foam should be
discharged to the destination before devices are removed.
nent damage to the device. These are stress ratings only; functional operation of
the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
*
DD
DD
+ 0.3 V
+ 0.3 V
–13–
MEMORY TIMING SPECIFICATIONS
The table below shows common memory device specifications
and the corresponding ADSP-2181 timing parameters, for your
convenience.
Memory
Device
Specification
Address Setup to
Address Setup to
Address Hold Time t
Data Setup Time
Data Hold Time
OE to Data Valid
Address Access Time t
xMS = PMS, DMS, BMS, CMS, IOMS.
FREQUENCY DEPENDENCY FOR TIMING
SPECIFICATIONS
t
with a frequency equal to half the instruction rate: a 16.67 MHz
input clock (which is equivalent to 60 ns) yields a 30 ns proces-
sor cycle (equivalent to 33 MHz). t
0.5t
rameters to obtain the specification value.
Example: t
CK
Write Start
Write End
is defined as 0.5t
CKI
period should be substituted for all relevant timing pa-
CKH
= 0.5t
CKI
CK
ADSP-2181 Timing
Timing
Parameter Definition
t
t
t
t
t
ASW
AW
WRA
DW
DH
RDD
AA
. The ADSP-2181 uses an input clock
– 7 ns = 0.5 (25 ns) – 7 ns = 8 ns
WARNING!
CK
Parameter
A0–A13, xMS Setup before
WR Low
A0–A13, xMS Setup before
WR Deasserted
A0–A13, xMS Hold after
WR Deasserted
Data Setup before WR
High
Data Hold after WR High
RD Low to Data Valid
A0–A13, xMS to Data Valid
values within the range of
ADSP-2181
ESD SENSITIVE DEVICE