ADSP-2181BST-133 Analog Devices Inc, ADSP-2181BST-133 Datasheet - Page 8

• Manufacturer Part Number: ADSP-2181BST-133
• Description: IC DSP CONTROLLER 16BIT 128TQFP
• Manufacturer: Analog Devices Inc
• Series: ADSP-21xxr
• Type: Fixed Pointr

Specifications of ADSP-2181BST-133

• Rohs Status: RoHS non-compliant
• Interface: Synchronous Serial Port (SSP)
• Clock Rate: 33.3MHz
• Non-volatile Memory: External
• On-chip Ram: 80kB
• Voltage - I/o: 5.00V
• Voltage - Core: 5.00V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 128-TQFP, 128-VQFP
• Device Core Size: 16b
• Architecture: Enhanced Harvard
• Format: Fixed Point
• Clock Freq (max): 33.3MHz
• Mips: 33.3
• Device Input Clock Speed: 33.3MHz
• Ram Size: 80KB
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (min): 4.5V
• Operating Supply Voltage (max): 5.5V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 128
• Package Type: TQFP
• Lead Free Status / RoHS Status: Not Compliant

ADSP-2181
There are 16,352 words of memory accessible internally when
the DMOVLAY register is set to 0. When DMOVLAY is set to
something other than 0, external accesses occur at addresses
0x0000 through 0x1FFF. The external address is generated as
shown in Table III.
DMOVLAY Memory A13
0
1
2
This organization allows for two external 8K overlays using only
the normal 14 address bits.
All internal accesses complete in one cycle. Accesses to external
memory are timed using the wait states specified by the DWAIT
register.
I/O Space
The ADSP-2181 supports an additional external memory space
called I/O space. This space is designed to support simple con-
nections to peripherals or to bus interface ASIC data registers.
I/O space supports 2048 locations. The lower eleven bits of the
external address bus are used; the upper three bits are unde-
fined. Two instructions were added to the core ADSP-2100
Family instruction set to read from and write to I/O memory
space. The I/O space also has four dedicated 3-bit wait state
registers, IOWAIT0-3, which specify up to seven wait states to
be automatically generated for each of four regions. The wait
states act on address ranges as shown in Table IV.
Composite Memory Select (CMS)
The ADSP-2181 has a programmable memory select signal that
is useful for generating memory select signals for memories
mapped to more than one space. The CMS signal is generated
to have the same timing as each of the individual memory select
signals (PMS, DMS, BMS, IOMS) but can combine their
functionality.
When set, each bit in the CMSSEL register, causes the CMS
signal to be asserted when the selected memory select is as-
serted. For example, to use a 32K word memory to act as both
program and data memory, set the PMS and DMS bits in the
CMSSEL register and use the CMS pin to drive the chip select
of the memory; use either DMS or PMS as the additional
address bit.
Address Range
0x000–0x1FF
0x200–0x3FF
0x400–0x5FF
0x600–0x7FF
Internal
External
Overlay 1
External
Overlay 2
Not Applicable
0
1
Table III.
Table IV.
Wait State Register
IOWAIT0
IOWAIT1
IOWAIT2
IOWAIT3
A12:0
Not Applicable
13 LSBs of Address
Between 0x0000
and 0x1FFF
13 LSBs of Address
Between 0x0000
and 0x1FFF
–8–
The CMS pin functions like the other memory select signals,
with the same timing and bus request logic. A 1 in the enable bit
causes the assertion of the CMS signal at the same time as the
selected memory select signal. All enable bits, except the BMS
bit, default to 1 at reset.
Byte Memory
The byte memory space is a bidirectional, 8-bit-wide, external
memory space used to store programs and data. Byte memory is
accessed using the BDMA feature. The byte memory space
consists of 256 pages, each of which is 16K 8.
The byte memory space on the ADSP-2181 supports read and
write operations as well as four different data formats. The byte
memory uses data bits 15:8 for data. The byte memory uses
data bits 23:16 and address bits 13:0 to create a 22-bit address.
This allows up to a 4 meg
used without glue logic. All byte memory accesses are timed by
the BMWAIT register.
Byte Memory DMA (BDMA)
The Byte memory DMA controller allows loading and storing of
program instructions and data using the byte memory space.
The BDMA circuit is able to access the byte memory space
while the processor is operating normally, and steals only one
DSP cycle per 8-, 16- or 24-bit word transferred.
The BDMA circuit supports four different data formats which
are selected by the BTYPE register field. The appropriate num-
ber of 8-bit accesses are done from the byte memory space to
build the word size selected. Table V shows the data formats
supported by the BDMA circuit.
BTYPE
00
01
10
11
Unused bits in the 8-bit data memory formats are filled with 0s.
The BIAD register field is used to specify the starting address
for the on-chip memory involved with the transfer. The 14-bit
BEAD register specifies the starting address for the external byte
memory space. The 8-bit BMPAGE register specifies the start-
ing page for the external byte memory space. The BDIR register
field selects the direction of the transfer. Finally the 14-bit
BWCOUNT register specifies the number of DSP words to
transfer and initiates the BDMA circuit transfers.
BDMA accesses can cross page boundaries during sequential
addressing. A BDMA interrupt is generated on the completion
of the number of transfers specified by the BWCOUNT register.
The BWCOUNT register is updated after each transfer so it can
be used to check the status of the transfers. When it reaches
zero, the transfers have finished and a BDMA interrupt is gener-
ated. The BMPAGE and BEAD registers must not be accessed
by the DSP during BDMA operations.
The source or destination of a BDMA transfer will always be
on-chip program or data memory, regardless of the values of
MMAP, PMOVLAY or DMOVLAY.
Internal
Memory Space
Program Memory
Data Memory
Data Memory
Data Memory
Table V.
8 (32 megabit) ROM or RAM to be
Word Size
24
16
8
8
Alignment
Full Word
Full Word
MSBs
LSBs
REV. D