XE8801AMI027LF Semtech, XE8801AMI027LF Datasheet - Page 91

• Manufacturer Part Number: XE8801AMI027LF
• Description: IC DAS 16BIT FLASH 8K MTP 44LQFP
• Manufacturer: Semtech

Specifications of XE8801AMI027LF

• Applications: Sensing Machine
• Core Processor: RISC
• Program Memory Type: FLASH (22 kB)
• Controller Series: XE8000
• Ram Size: 512 x 8
• Interface: UART, USRT
• Number Of I /o: 24
• Voltage - Supply: 2.4 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 44-LQFP
• For Use With: XE8000MP - PROG BOARD AND PROSTART2 CARD
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

16.4.2
Figure 16-2 shows a detailed functional diagram of the ZoomingADC™. In
Table 16-10 the configuration of the peripheral registers is detailed. The system has a bank of eight 8-bit registers:
six registers are used to configure the acquisition chain (RegAcCfg0 to 5), and two registers are used to store the
output code of the analog-to-digital conversion (RegAcOutMsb & Lsb). The register coding of the ADC parameters
and performance characteristics are detailed in Section 16.7.
With:
•
•
•
•
•
•
•
•
•
•
© Semtech 2005
OUT: (r) digital output code of the analog-to-digital converter. (MSB = OUT[15])
START: (w) setting this bit triggers a single conversion (after the current one is finished). This bit always reads
back 0.
SET_NELC: (rw) sets the number of elementary conversions to 2
input signal is chopped between elementary conversions (1,2,4,8).
SET_OSR: (rw) sets the over-sampling rate (OSR) of an elementary conversion to 2
32, ..., 512, 1024.
CONT: (rw) setting this bit starts a conversion. A new conversion will automatically begin as long as the bit
remains at 1.
TEST: bit only used for test purposes. In normal mode, this bit is forced to 0 and cannot be overwritten.
IB_AMP_ADC: (rw) sets the bias current in the ADC to 0.25*(1+ IB_AMP_ADC[1:0]) of the normal operation
current (25, 50, 75 or 100% of nominal current). To be used for low-power, low-speed operation.
IB_AMP_PGA: (rw) sets the bias current in the PGAs to 0.25*(1+IB_AMP_PGA[1:0]) of the normal operation
current (25, 50, 75 or 100% of nominal current). To be used for low-power, low-speed operation.
ENABLE: (rw) enables the ADC modulator (bit 0) and the different stages of the PGAs (PGAi by bit i=1,2,3). PGA stages that
are disabled are bypassed.
FIN: (rw) These bits set the sampling frequency of the acquisition chain. Expressed as a fraction of the oscillator frequency,
the sampling frequency is given as: 00
RegAcOutMsb
RegAcOutLsb
RegAcCfg0
RegAcCfg1
RegAcCfg2
RegAcCfg3
RegAcCfg4
RegAcCfg5
Register
Default
values:
Default
values:
Default
values:
Default
values:
Default
values:
Default
values:
Name
Peripheral Registers
Table 16-10. Peripheral registers to configure the acquisition chain (AC)
BUSY
STAR
IB_AMP_ADC[
PGA1
_G
7
T
0
0
0
0
FIN[1:0]
and to store the analog-to-digital conversion (ADC) result
1:0]
11
00
SET_NELC[1:0]
DEF
0
6
01
1/4 f
PGA2_GAIN[1:0]
IB_AMP_PGA[1:
5
RC
, 01
11
00
0]
1/8 f
Bit Position
4
PGA3_OFFSET[6:0]
OUT[15:8]
16-6
OUT[7:0]
PGA3_GAIN[6:0]
RC
SET_OSR[2:0]
AMUX[4:0]
, 10
0000000
0000000
00000
010
3
1/32 f
PGA2_OFFSET[3:0]
RC
SET_NELC[1:0]
, 11
ENABLE[3:0]
2
0001
0000
~8kHz.
CONT
. To compensate for offsets, the
XE8801A – SX8801R
1
0
(3+SET_OSR[2:0])
VMUX
TEST
0
0
0
www.semtech.com
. OSR = 8, 16,