CS42436-DMZ Cirrus Logic Inc, CS42436-DMZ Datasheet - Page 35

• Manufacturer Part Number: CS42436-DMZ
• Description: IC CODEC 108DB 192KHZ 52-MQFP
• Manufacturer: Cirrus Logic Inc
• Type: Audio Codecr

Specifications of CS42436-DMZ

• Data Interface: Serial
• Resolution (bits): 24 b
• Number Of Adcs / Dacs: 6 / 6
• Sigma Delta: Yes
• Dynamic Range, Adcs / Dacs (db) Typ: 105 / 108 (Differential), 102 / 105 (Single-Ended)
• Voltage - Supply, Analog: 3.14 V ~ 5.25 V
• Voltage - Supply, Digital: 3.14 V ~ 3.47 V
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: 52-MQFP, 52-PQFP
• Audio Codec Type: Stereo
• No. Of Adcs: 6
• No. Of Dacs: 6
• No. Of Input Channels: 6
• No. Of Output Channels: 6
• Adc / Dac Resolution: 24bit
• Sampling Rate: 200kSPS
• Ic Interface Type: I2C
• Package: 52MQFP
• Adc/dac Resolution: 24 Bit
• Number Of Channels: 6ADC /6 DAC
• Number Of Dacs: 6
• Operating Supply Voltage: 3.3|5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 598-1613

DS647F2
5.6.4
5.7
5.7.1
AUX_LRCK
AUX_SCLK
AUX_SDIN
Control Port Description and Timing
The control port is used to access the registers, in Software Mode, allowing the CS42436 to be configured
for the desired operational modes and formats. The operation of the control port may be completely asyn-
chronous with respect to the audio sample rates. However, to avoid potential interference problems, the
control port pins should remain static if no operation is required.
The control port has two modes: SPI and I²C, with the CS42436 acting as a slave device. SPI Mode is se-
lected if there is a high-to-low transition on the AD0/CS pin, after the RST pin has been brought high. I²C
Mode is selected by connecting the AD0/CS pin through a resistor to VLC or DGND, thereby permanently
selecting the desired AD0 bit address state.
Left-Justified
SPI Mode
In SPI Mode, CS is the CS42436 chip-select signal, CCLK is the control port bit clock (input into the
CS42436 from the microcontroller), CDIN is the input data line from the microcontroller, CDOUT is the
output data line to the microcontroller. Data is clocked in on the rising edge of CCLK and out on the falling
edge.
Figure 17
first seven bits on CDIN form the chip address and must be 1001111. The eighth bit is a read/write indi-
cator (R/W), which should be low to write. The next eight bits form the Memory Address Pointer (MAP),
which is set to the address of the register that is to be updated. The next eight bits are the data which will
be placed into the register designated by the MAP. During writes, the CDOUT output stays in the Hi-Z
state. It may be externally pulled high or low with a 47 kΩ resistor, if desired.
There is a MAP auto-increment capability, enabled by the INCR bit in the MAP register. If INCR is a zero,
the MAP will stay constant for successive read or writes. If INCR is set to a 1, the MAP will auto-increment
after each byte is read or written, allowing block reads or writes of successive registers.
To read a register, the MAP has to be set to the correct address by executing a partial write cycle which
finishes (CS high) immediately after the MAP byte. The MAP auto-increment bit (INCR) may be set or not,
as desired. To begin a read, bring CS low, send out the chip address and set the read/write bit (R/W) high.
The next falling edge of CCLK will clock out the MSB of the addressed register (CDOUT will leave the high
impedance state). If the MAP auto-increment bit is set to 1, the data for successive registers will appear
consecutively.
M S B
shows the operation of the control port in SPI Mode. To write to a register, bring CS low. The
L e ft C h a n n el
AUX1
Figure 16. AUX Left-Justified Format
L S B
M S B
R ig ht C h a n n el
AUX2
L S B
CS42436
MSB
35