TEA1062A NXP Semiconductors, TEA1062A Datasheet - Page 26

• Manufacturer Part Number: TEA1062A
• Manufacturer: NXP Semiconductors

Specifications of TEA1062A

• Primary Target Application: Telephone Sets
• Operating Supply Voltage (typ): 2.7/3.4V
• Max Transmitter Gain: 53.5dB
• Receiver Gain (max): 32.5dB
• Operating Temp Range: -25C to 75C
• Package Type: PDIP
• Pin Count: 16
• Operating Current: 900uA
• Operating Temperature Classification: Commercial
• Mounting: Through Hole
• Operating Supply Voltage (min): 2.2V
• Lead Free Status / Rohs Status: Compliant

Philips Semiconductors
SOLDERING
Plastic dual in-line packages
B
The maximum permissible temperature of the solder is
260 C; this temperature must not be in contact with the
joint for more than 5 s. The total contact time of successive
solder waves must not exceed 5 s.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified storage maximum. If the printed-circuit board has
been pre-heated, forced cooling may be necessary
immediately after soldering to keep the temperature within
the permissible limit.
R
Apply the soldering iron below the seating plane (or not
more than 2 mm above it). If its temperature is below
300 C, it must not be in contact for more than 10 s; if
between 300 and 400 C, for not more than 5 s.
Plastic small-outline packages
B
During placement and before soldering, the component
must be fixed with a droplet of adhesive. After curing the
adhesive, the component can be soldered. The adhesive
can be applied by screen printing, pin transfer or syringe
dispensing.
Maximum permissible solder temperature is 260 C, and
maximum duration of package immersion in solder bath is
10 s, if allowed to cool to less than 150 C within 6 s.
Typical dwell time is 4 s at 250 C.
A modified wave soldering technique is recommended
using two solder waves (dual-wave), in which a turbulent
wave with high upward pressure is followed by a smooth
laminar wave. Using a mildly-activated flux eliminates the
need for removal of corrosive residues in most
applications.
1997 Sep 03
Y DIP OR WAVE
Y WAVE
EPAIRING SOLDERED JOINTS
Low voltage transmission circuits with
dialler interface
26
B
Reflow soldering requires the solder paste (a suspension
of fine solder particles, flux and binding agent) to be
applied to the substrate by screen printing, stencilling or
pressure-syringe dispensing before device placement.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt, infrared, and
vapour-phase reflow. Dwell times vary between 50 and
300 s according to method. Typical reflow temperatures
range from 215 to 250 C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 min at 45 C.
R
IRON OR PULSE
Fix the component by first soldering two, diagonally
opposite, end pins. Apply the heating tool to the flat part of
the pin only. Contact time must be limited to 10 s at up to
300 C. When using proper tools, all other pins can be
soldered in one operation within 2 to 5 s at between 270
and 320 C. (Pulse-heated soldering is not recommended
for SO packages.)
For pulse-heated solder tool (resistance) soldering of VSO
packages, solder is applied to the substrate by dipping or
by an extra thick tin/lead plating before package
placement.
Y SOLDER PASTE REFLOW
EPAIRING SOLDERED JOINTS
-
HEATED SOLDER TOOL
TEA1062; TEA1062A
(
BY HAND
)
Product specification
-
HELD SOLDERING