TDA9110 STMicroelectronics, TDA9110 Datasheet - Page 16

• Manufacturer Part Number: TDA9110
• Description: Deflection Processor 32-Pin SPDIP
• Manufacturer: STMicroelectronics

Specifications of TDA9110

• Package: 32SPDIP
• Operating Temperature: 0 to 70 °C

TDA9110
OPERATING DESCRIPTION (continued)
Of course, when the choice is done, we can refresh
the synchro detectionsand verify that the extracted
Vsync is present and that no synchro type change
have occured.
Synchro processor is also giving synchro polarity
information.
I.7 - IC status
TheIC can inform the MCUabout the 1st Horizontal
PLL or Vertical section status (locked or not), and
about the Xray protection (activated or not).
Resettingthe Xray internal latch can be done either
by decreasing the V
via the I
I.8 - Synchro Inputs
Both H/HVin and Vsyncin inputs are TTL compat-
ible triggers with Hysterisis to avoid erratic detec-
tion. It includes pull up resistor to V
I.9 - Synchro Processor Output
The synchro processor delivers the Hlockout signal
on a TTL-compatible CMOS output.
Hlockout is the Horizontal 1st PLL status (5V when
locked). It allows the MCU to check the Horizontal
IC locking.
II - HORIZONTAL PART
II.1 - Internal Input Conditions
A digital signal (Horizontal synchro pulse or TTL
composite) is sent by the synchro processor to the
horizontal part.
Positive or negative signal can be applied to the
Horizontal part input (see Figure 6).
Using internal integration, both signals are recog-
nized if Z/T < 25%. Synchronization occurs on the
leading edge of the internal synchro signal. The
minimum value of Z is 0.7 s.
Figure 6
An other integration is able to extract vertical pulse
of composite synchro if duty cycle is higher than
25% (typically d = 35%) (see Figure 7).
16/29
2
C interface.
CC
supply or directly resetting
DD
.
Figure 7
The last feature performed is the removing of
equalizing pulses to avoid parasitic pulses on
phase comparator input (which is sensitive to
wrong or missing pulses).
II.2 - PLL1
The PLL1 consists of a phase comparator, an exter-
nal filter and a voltage control oscillator (VCO).
The phase comparator is a ”phase frequency” type
designed in CMOS technology. This kind of phase
detector avoids locking on false frequencies. It is
followed by a ”charge pump”, composed of two
current sources sunk and sourced(Typically I = 1mA
when locked and I = 140 A when unlocked). This
difference between lock/unlock permits a smooth
catching of the horizontal frequency by the PLL1.
This effect is reinforced by an internal original slow
down system when the PLL1 is locked, avoiding the
Horizontal frequency to change too fast.
The dynamic behaviour of the PLL1 is fixed by an
external filter which integrates the current of the
charge pump. A ”CRC” filter is generally used (see
Figure 8).
Figure 8
ThePLL1isinternallyinhibitedduringextractedvertical
synchro (if any) to avoid taking in account missing
pulses or wrong pulses on phase comparator.The
inhibition results from the opening of a switch located
betweenthe chargepumpand thefilter (see Figure 9).
The VCO uses an external RC network. It delivers
a linear sawtooth obtained by the charge and the
discharge of the capacitor, with a current propor-
tionnal to the current in the resistor. The typical
thresholds of the sawtooth are 1.6V and 6.4V.
C
TRAMEXT
PLL1F
d
7
d