TFA9810T/N1,118 NXP Semiconductors, TFA9810T/N1,118 Datasheet - Page 6

• Manufacturer Part Number: TFA9810T/N1,118
• Description: IC AMP AUDIO 15W STER D 32SOIC
• Manufacturer: NXP Semiconductors
• Type: Class Dr

Specifications of TFA9810T/N1,118

• Output Type: 2-Channel (Stereo)
• Package / Case: 32-SOIC (7.5mm Width)
• Max Output Power X Channels @ Load: 15W x 2 @ 8 Ohm
• Voltage - Supply: 8 V ~ 20 V
• Features: Short-Circuit and Thermal Protection
• Mounting Type: Surface Mount
• Product: Class-D
• Output Power: 15 W
• Available Set Gain: 19.7 dB
• Thd Plus Noise: 0.04 %
• Operating Supply Voltage: 12 V
• Maximum Power Dissipation: 2500 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Audio Load Resistance: 8 Ohms
• Input Bias Current (max): 1 uA
• Input Signal Type: Differential
• Minimum Operating Temperature: - 40 C
• Output Signal Type: Differential
• Supply Type: Single
• Supply Voltage (max): 20 V
• Supply Voltage (min): 8 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 935280404118; TFA9810T-T; TFA9810T-T

NXP Semiconductors
TFA9810_3
Product data sheet
8.3.1 Operating in self-oscillating configuration
8.3.2 Operating in open-loop configuration
8.3 Input comparators
8.4 Diagnostic
8.5 Protections
In SLEEP mode the TFA9810 is not biased and has a very low supply current.
When the TFA9810 is set to OPERATING mode the device is started via the start-up
sequence, which provides a pop-free start-up behavior. After start-up the reference
voltages STAB are present and the outputs start switching.
Table 5.
The input stages have a differential input and are optimized for low noise and low offset.
This results in maximum flexibility in the application.
The inputs (IN1P, IN1N, IN2P, IN2N) of the comparators are internally set to a voltage level
of 0.5V
high-ohmic.
No internal voltages are applied to the inputs. The input pins (IN1P, IN1N, IN2P, IN2N) are
pulled down to V
The DIAG output is an open-drain output. The maximum current is 2 mA. Whenever one
of the protections is triggered the DIAG output is activated low. The DIAG output refers to
V
Overtemperature, overcurrent, overvoltage, undervoltage, overdissipation sensors, and
window protection are included in the TFA9810. When one of these sensors exceeds its
threshold level either the output power stage is switched off and the outputs (OUT1N,
OUT1P, OUT2N, OUT2P) become floating, or the TFA9810 shuts down and starts up
immediately.
Interfacing
ENABLE [V]
ENABLE < 0.8 V
ENABLE > 3 V
SSD
•
•
OverTemperature Protection (OTP)
If the junction temperature (T
outputs become floating. The device will start switching again after 5 s and when the
temperature is below 150 C. This is thermal limitation without audible interruptions.
OverCurrent Protection (OCP)
If the output current exceeds the maximum output current threshold level the output
becomes floating. The device will start switching again after 5 s. This is current
limitation without audible interruptions.
.
P
, but only during the start-up sequence. In operating mode the inputs are
Start-up
SSA
level by internal resistors.
Rev. 03 — 20 February 2008
j
) exceeds a threshold level of about 150 C then the
Mode
SLEEP
OPERATING
Audio amplifier 2 x 12 W
© NXP B.V. 2008. All rights reserved.
TFA9810
6 of 29