AT89C5131A-M Atmel Corporation, AT89C5131A-M Datasheet - Page 134
AT89C5131A-M
Manufacturer Part Number
AT89C5131A-M
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT89C5130A-M.pdf
(188 pages)
2.AT89C5130A-M.pdf
(4 pages)
3.AT89C5130A-M.pdf
(34 pages)
Specifications of AT89C5131A-M
Flash (kbytes)
32 Kbytes
Max. Operating Frequency
48 MHz
Cpu
8051-12C
Max I/o Pins
34
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
1
Twi (i2c)
1
Uart
1
Sram (kbytes)
1.25
Eeprom (bytes)
1024
Self Program Memory
API
Operating Voltage (vcc)
2.7 to 5.5
Timers
4
Isp
UART/USB
Watchdog
Yes
- Current page: 134 of 188
- Download datasheet (2Mb)
21.8.2
21.8.3
134
AT89C5130A/31A-M
Resume
Upstream Resume
The stop of the 48 MHz clock from the PLL should be done in the following order:
When the USB controller is in Suspend state, the Resume detection is active even if all the
clocks are disabled and if the C51 is in Idle or Power-down mode. The WUPCPU bit is set by
hardware when a non-idle state occurs on the USB bus. This triggers an interrupt if enabled.
This interrupt wakes up the CPU from its Idle or Power-down state and the interrupt function is
then executed. The firmware will first enable the 48 MHz generation and then reset to 0 the
SUSPCLK bit in the USBCON register if needed.
The firmware has to clear the SPINT bit in the USBINT register before any other USB operation
in order to wake up the USB controller from its Suspend mode.
The USB controller is then re-activated.
Figure 21-11. Example of a Suspend/Resume Management
A USB device can be allowed by the Host to send an upstream resume for Remote Wake Up
purpose.
1. Clear suspend interrupt bit in USBINT (required to allow the USB pads to enter power
2. Enable USB resume interrupt.
3. Disable of the 48 MHz clock input of the USB controller by setting to 1 the SUSPCLK bit
4. Disable the PLL by clearing the PLLEN bit in the PLLCON register.
5. Make the CPU core enter power down mode by setting PDOWN bit in PCON.
down mode).
in the USBCON register.
Detection of a SUSPEND State
Detection of a RESUME State
WUPCPU
SPINT
microcontroller in Power-down
Clear WUPCPU Bit
USB Controller Init
Clear SUSPCLK
Set SUSPCLK
Clear SPINT
Disable PLL
Enable PLL
4337K–USB–04/08
Related parts for AT89C5131A-M
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
8-bit microcontroller with 4K bytes flash, 5V, 20MHz
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit microcontroller with 4K bytes flash, 5V, 20MHz
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-Bit Microcontroller with 4K Bytes Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Microcontroller with 4K Bytes Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Microcontroller With 4k Bytes Flash
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
IC 8051 MCU 64K FLASH 44-VQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 16K 24SOIC
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 16K 32VQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 32K 64BGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 64K 52PLCC
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 64K 64VQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU 16K FLASH 32-VQFP
Manufacturer:
Atmel
Datasheet: