ATxmega16D4 Atmel Corporation, ATxmega16D4 Datasheet - Page 170

• Manufacturer Part Number: ATxmega16D4
• Manufacturer: Atmel Corporation

Specifications of ATxmega16D4

• Flash (kbytes): 16 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Speed: No
• Usb Interface: No
• Spi: 4
• Twi (i2c): 2
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 12
• Adc Speed (ksps): 200
• Analog Comparators: 2
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 14
• Input Capture Channels: 14
• Pwm Channels: 14
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

16.3
8210B–AVR–04/10
General TWI Bus Concepts
It is possible to disable the internal TWI drivers in the device, and enabling a 4-wire interface for
connecting external bus drivers.
The Two-Wire Interface (TWI) provides a simple two-wire bi-directional bus consisting of a serial
clock line (SCL) and a serial data line (SDA). The two lines are open collector lines (wired-AND),
and pull-up resistors (Rp) are the only external components needed to drive the bus. The pull-up
resistors will provide a high level on the lines when none of the connected devices are driving
the bus. A constant current source can be used as an alternative to the pull-up resistors.
The TWI bus is a simple and efficient method of interconnecting multiple devices on a serial bus.
A device connected to the bus can be a master or slave, where the master controls the bus and
all communication.
Figure 16-1
Figure 16-1. TWI Bus Topology
A unique address is assigned to all slave devices connected to the bus, and the master will use
this to address a slave and initiate a data transaction. 7-bit or 10-bit addressing can be used.
Several masters can be connected to the same bus, and this is called a multi-master environ-
ment. An arbitration mechanism is provided for resolving bus ownership between masters since
only one master device may own the bus at any given time.
A device can contain both master and slave logic, and can emulate multiple slave devices by
responding to more than one address.
A master indicates the start of transaction by issuing a START condition (S) on the bus. An
address packet with a slave address (ADDRESS) and an indication whether the master wishes
to read or write data (R/W), is then sent. After all data packets (DATA) are transferred, the mas-
ter issues a STOP condition (P) on the bus to end the transaction. The receiver must
acknowledge (A) or not-acknowledge (A) each byte received.
Figure 16-2
SDA
SCL
V
CC
illustrates the TWI bus topology.
shows a TWI transaction.
R
P
R
P
DEVICE #1
TWI
R
S
R
S
DEVICE #2
TWI
R
S
R
S
XMEGA D
Note: R
DEVICE #N
TWI
R
S
S
is optional
R
S
170