IC EQUALIZER VIDEO 3D+C 48LLP

DS16EV5110ASQE/NOPB

Manufacturer Part NumberDS16EV5110ASQE/NOPB
DescriptionIC EQUALIZER VIDEO 3D+C 48LLP
ManufacturerNational Semiconductor
TypeVideo Equalizer
DS16EV5110ASQE/NOPB datasheet
 


Specifications of DS16EV5110ASQE/NOPB

ApplicationsHD Displays, DVI/HDMIMounting TypeSurface Mount
Package / Case48-LLPSupply Voltage Range3V To 3.6V
Operating Temperature Range-40°C To +85°CDigital Ic Case StyleLLP
No. Of Pins48MslMSL 3 - 168 Hours
Filter TerminalsSMDNo. Of I/o's8
Rohs CompliantYesCommunication FunctionMulti-Channel Equalizer
Lead Free Status / RoHS StatusLead free / RoHS CompliantOther namesDS16EV5110ASQETR
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
11
12
13
14
15
16
17
18
19
20
Page 1/20

Download datasheet (2Mb)Embed
Next
Video Equalizer (3D+C) for DVI, HDMI Source/Repeater/
Sink Applications
General Description
The DS16EV5110A is a multi-channel equalizer optimized for
video cable extension Source/Repeater/Sink Applications. It
operates between 250Mbps and 2.25Gbps with common ap-
plications at 1.65Gbps and 2.25Gbps (per data channel). It
contains three Transition-Minimized Differential Signaling
(TMDS) data channels and one clock channel as specified for
DVI and HDMI interfaces. It provides compensation for skin-
effect and dielectric losses, a common phenomenon when
transmitting video on commercially available high definition
video cables.
The inputs conform to DVI and HDMI requirements and fea-
tures programmable levels of input equalization. The pro-
grammable levels of equalization provide optimal signal boost
and reduces inter-symbol interference. Eight levels of boost
are selectable via a pin interface or by the optional System
Management Bus.
The clock channel is optimized for clock rates of up to 225
MHz and features a signal detect circuit. To maximize noise
immunity, the DS16EV5110A features a signal detector with
programmable thresholds. The threshold is adjustable
through a System Management Bus (SMBus) interface.
The DS16EV5110A may be used in Source Applications, Sink
Applications, or as a Repeater.
The DS16EV5110A also provides support for system power
management via output enable controls. Additional controls
are provided via the SMBus enabling customization and op-
timization for specific applications requirements. These con-
trols include programmable features such as output ampli-
tude and boost controls as well as system level diagnostics.
The DS16EV5110A is a pin-for-pin replacement to the
DS16EV5110. It features an enhanced CML output that
presents a high impedance when powered down.
Typical Application
© 2009 National Semiconductor Corporation
DS16EV5110A
Features
8 levels of equalization settable by 3 pins or through the
SMBus interface
DC-Coupled inputs and outputs
Optimized for operation from 250 Mbps to 2.25 Gbps in
support of UXGA, 480 I/P, 720 I/P, 1080 I, and 1080 P with
8, 10, and 12–bit Color Depth Resolutions
Two DS16EV5110A devices support DVI/HDMI Dual Link
DVI 1.0, and HDMI 1.3a Compatible TMDS Interface
Clock channel signal detect (LOS)
Enable for power savings standby mode
System Management Bus (SMBus) provides control of
boost, output amplitude, enable, and clock channel signal
detect threshold
Low power consumption: 475mW (Typical)
0.13 UI total jitter at 1.65 Gbps including cable
Single 3.3V power supply
Small 7mm x 7mm, 48-pin leadless LLP package
-40°C to +85°C operating temperature range
Extends TMDS cable reach over:
1.
> 40 meters 24 AWG DVI Cable (1.65Gbps)
2.
> 20 meters 28 AWG DVI Cable (1.65Gbps)
3.
> 20 meters Cat5/Cat5e/Cat6 cables (1.65Gbps)
4.
> 20 meters 28 AWG HDMI cables (2.25Gbps)
Applications
HDMI / DVI Cable Extenders
HDMI / DVI Switches
Projectors
High Definition Displays
300646
April 6, 2009
30064653
www.national.com

DS16EV5110ASQE/NOPB Summary of contents

  • Page 1

    ... The DS16EV5110A is a pin-for-pin replacement to the DS16EV5110. It features an enhanced CML output that presents a high impedance when powered down. Typical Application © 2009 National Semiconductor Corporation DS16EV5110A Features ■ 8 levels of equalization settable by 3 pins or through the SMBus interface ■ ...

  • Page 2

    Pin Descriptions Pin Name Pin Number I/O, Type HIGH SPEED DIFFERENTIAL I/O C_IN− CML C_IN+ 2 D_IN0− CML D_IN0+ 5 D_IN1− CML D_IN1+ 9 D_IN2− CML D_IN2+ 12 C_OUT CML ...

  • Page 3

    Connection Diagram TOP VIEW — Not to Scale NSID DS16EV5110ASQ DS16EV5110ASQX Ordering Information Tape & Reel Quantity 250 2,500 3 30064652 Package SQA48D SQA48D www.national.com ...

  • Page 4

    ... Absolute Maximum Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage ( LVCMOS Input Voltage LVCMOS Output Voltage CML Input/Output Voltage Junction Temperature Storage Temperature Lead Temp. (Soldering, 5 sec.) Electrical Characteristics Over recommended operating supply and temperature ranges unless other specified ...

  • Page 5

    Symbol Parameter t Inter Pair Channel-to-Channel CCSK Skew (all 4 Channels) t Latency D OUTPUT JITTER TJ1 Total Jitter at 1.65 Gbps TJ2 Total Jitter at 2.25 Gbps TJ3 Total Jitter at 165 MHz TJ4 Total Jitter at 225 MHz ...

  • Page 6

    Electrical Characteristics — System Management Bus Interface Over recommended operating supply and temperature ranges unless other specified. Symbol Parameter System Bus Interface — DC Specifications V Data, Clock Input Low Voltage IL V Data, Clock Input High Voltage IH I ...

  • Page 7

    Timing Diagrams FIGURE 2. Test Setup Diagram for Jitter Measurement FIGURE 1. SMBus Timing Diagram 7 30064650 30064627 www.national.com ...

  • Page 8

    System Management Bus (SMBus) and Configuration Registers The System Management Bus interface is compatible to SM- Bus 2.0 physical layer specification. The use of the Chip Select signal is required. Holding the CS pin High enables the SMBus port allowing ...

  • Page 9

    Name Address Default Type Bit 7 0x00 0x00 RO Status 0x01 0x00 RO Status Status 0x02 0x00 RO Internal 0x03 0x77 RW Enable/ Individual Channel Boost Control for C_IN±, D_IN0± Individual 0x04 0x77 RW Channel Boost Control for D_IN1±, D_IN2± ...

  • Page 10

    DS16EV5110A Device Description The DS16EV5110A video equalizer comprises three data channels, a clock channel, and a control interface including a Systeml Management Bus (SMBus) port. DATA CHANNELS The DS16EV5110A provides three data channels. Each data channel consists of an equalizer ...

  • Page 11

    OUTPUT LEVEL CONTROL The output amplitude of the TMDS drivers for both the data channels and the clock channel can be controlled via the SM- Bus (see Table 1). The default output level is 1000mV p-p. The following Table presents ...

  • Page 12

    Application Information The DS16EV5110A is used to recondition DVI/HDMI video signals or differential signals with similar characteristics for signal loss and degradation due to transmission through a length of shielded or unshielded cable. The DS16EV5110A maybe used on the Source ...

  • Page 13

    In general, the use of multiple equalizers is not recommended due to accumulation of random jitter. DVI 1.0 AND HDMI V1.2a APPLICATIONS A single DS16EV5110A can be used to implement cable ex- tension solutions with various resolutions and screen refresh ...

  • Page 14

    CABLE SELECTION At higher frequencies, longer cable lengths produce greater losses due to the skin effect. The quality of the cable with respect to conductor wire gauge and shielding heavily influ- ences performance. Thicker conductors have lower signal degradation per ...

  • Page 15

    General Recommendations The DS16EV5110A is a high performance circuit capable of delivering excellent performance. Careful attention must be paid to the details associated with high-speed design as well as providing a clean power supply. Refer to the LVDS Owner’s Manual ...

  • Page 16

    Typical Performance Characteristics FIGURE 13. Un-Equalized vs. Equalized Signal after 25m of 28 AWG DVI Cable at 1.65 Gbps (0x06 Setting) FIGURE 14. Output Signal after 20m of Cat5 Cable at 1.65 Gbps (0x06 Setting) FIGURE 15. Output Signal after ...

  • Page 17

    FIGURE 16. Output Signal after 0. AWG DVI Cable at 1.65 Gbps (0x04 Setting) FIGURE 17. Output Signal after 20m of 28 AWG HDMI Cable at 2.25 Gbps (0x06 Setting) 30064633 30064634 17 www.national.com ...

  • Page 18

    Physical Dimensions www.national.com inches (millimeters) unless otherwise noted 7mm x 7mm 48-pin LLP Package Order Number DS16EV5110ASQ Package Number SQA48D 18 ...

  • Page 19

    Notes 19 www.national.com ...

  • Page 20

    ... For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Amplifiers www.national.com/amplifiers Audio www.national.com/audio Clock and Timing www.national.com/timing Data Converters www.national.com/adc Interface www.national.com/interface LVDS www.national.com/lvds Power Management www.national.com/power Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www ...