BTS 6480SF Infineon Technologies, BTS 6480SF Datasheet - Page 11

• Manufacturer Part Number: BTS 6480SF
• Manufacturer: Infineon Technologies

Specifications of BTS 6480SF

• Packages: PG-DSO-36
• Channels: 4.0
• Channel Mix: 2*4,5mohm+2*11mohm
• Led Mode: Yes
• Cranking Mode: No
• Pwm Engine Integrated: Yes

Absolute Maximum Ratings (cont’d)
T
(unless otherwise specified)
Pos.
4.1.20 Current through serial output pin SO
PWM Clock and Sense Synchronization Pin
4.1.21 Voltage at PWM clock input pin
4.1.22 Current through PWM clock input pin
4.1.23 Voltage at sense synchronization pin
4.1.24 Current through sense synchronization pin
Limp Home Pin
4.1.25 Voltage at limp home input pin
4.1.26 Current through limp home input pin
External Driver Pins
4.1.27 Voltage at external driver output
4.1.28 Current through external driver output
4.1.29 Voltage at external driver diagnosis enable
4.1.30 Current through external driver diagnosis enable
Temperatures
4.1.31 Junction temperature
4.1.32 Dynamic temperature increase while switching
4.1.33 Storage temperature
ESD Susceptibility
4.1.34 ESD susceptibility HBM
1) Not subject to production test, specified by design.
2) Device is mounted on an FR4 2s2p board according to Jedec JESD51-2,-5,-7 at natural convection; The product
3) In accordance to AEC Q100-012 and AEC Q101-006.
4) R
5) Over current protection is a protection feature. Operation in over current protection is considered as “outside” normal
6) Pulse shape represents inductive switch off: I
7) ESD resistivity, HBM according to EIA/JESD 22-A 114B (1.5 k , 100 pF)
Note: Stresses above the ones listed here may cause permanent damage to the device. Exposure to absolute
Note: Integrated protection functions are designed to prevent IC destruction under fault conditions described in the
Data Sheet
j
= -40 to +150 C; all voltages with respect to ground
(chip+package) was simulated on a 76.4 x 114.3 x 1.5 mm board with 2 inner copper layers (2 x 70 µm Cu, 2 x 35 µm Cu).
Where applicable, a thermal via array under the package contacted the first inner copper layer.
operating range. Protection features are not designed for continuous repetitive operation.
I
is the internal resistance of the load dump pulse generator.
maximum rating conditions for extended periods may affect device reliability.
data sheet. Fault conditions are considered as “outside” normal operating range. Protection functions are
not designed for continuous repetitive operation.
Parameter
other pins incl. OUT vs. GND
1)
OUT pins vs. VBB
D(t)
= I
D
(0)
11
(1 - t / t
Symbol
I
V
I
V
I
V
I
V
I
V
I
T
T
V
SO
PLCK
ISSY
LHI
EDO
EDD
j
T
stg
PCLK
ISSY
LHI
EDO
EDD
ESD
j
pulse
); 0 < t < t
min.
-2.0
-0.3
-0.75
-2.0
-0.3
-2.0
-0.3
-0.75
-2.0
-0.3
-1.0
-0.3
-1.0
-40
–
-55
-4
-2
Limit Values
pulse
max.
2.0
V
0.75
2.0
V
2.0
5.5
0.75
2.0
V
1.0
V
1.0
150
60
150
4
2
DD
DD
DD
DD
+ 0.3 V
+ 0.3 V
+ 0.3 V
+ 0.3 V
Electrical Characteristics
SPOC - BTS6480SF
Unit Conditions
mA
mA –
mA
V
mA –
mA
mA
K
kV
C
C
Rev. 1.0, 2010-04-12
t
–
t
–
t
–
t
–
t
–
t
–
–
–
HBM
–
–
2 min.
2 min.
2 min.
2 min.
2 min.
2 min.
7)