IS63LV1024 Integrated Silicon Solution, Inc., IS63LV1024 Datasheet
IS63LV1024
Available stocks
Related parts for IS63LV1024
IS63LV1024 Summary of contents
Page 1
... CE OE and When CE is HIGH (deselected), the device assumes a standby mode at which the power dissipation can be reduced down to 250 µW (typical) with CMOS input levels. The IS63LV1024/IS63LV1024L operates from a single 3.3V power supply and all inputs are TTL-compatible. DECODER MEMORY ARRAY I/O DATA ...
Page 2
... IS63LV1024 IS63LV1024L PIN CONFIGURATION 32-Pin SOJ I/ I/ VDD 8 25 GND PIN DESCRIPTIONS A0-A16 Address Inputs CE Chip Enable Input OE Output Enable Input WE Write Enable Input ...
Page 3
... IS63LV1024 IS63LV1024L TRUTH TABLE Mode Not Selected X H (Power-down) Output Disabled H L Read H L Write L L ABSOLUTE MAXIMUM RATINGS Symbol Parameter V Terminal Voltage with Respect to GND TERM T Storage Temperature STG P Power Dissipation T Notes: 1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied ...
Page 4
... 0.2V Notes address and data inputs are cycling at the maximum frequency means no input lines change. MAX 2. Typical values are measured 3.3V IS63LV1024L POWER SUPPLY CHARACTERISTICS Symbol Parameter Test Conditions = Max Operating ...
Page 5
... IS63LV1024 IS63LV1024L READ CYCLE SWITCHING CHARACTERISTICS Symbol Parameter t Read Cycle Time RC t Address Access Time AA t Output Hold Time OHA CE Access Time t ACE OE Access Time t DOE OE to Low-Z Output t (2) LZOE OE to High-Z Output t (2) HZOE CE to Low-Z Output t (2) LZCE ...
Page 6
... IS63LV1024 IS63LV1024L AC WAVEFORMS (1,2) READ CYCLE NO. 1 ADDRESS D OUT PREVIOUS DATA VALID READ CYCLE NO. 2 (1,3) ADDRESS LZCE HIGH-Z D OUT Notes HIGH for a Read Cycle. 2. The device is continuously selected. OE Address is valid prior to or coincident with CE LOW transitions ...
Page 7
... IS63LV1024 IS63LV1024L WRITE CYCLE SWITCHING CHARACTERISTICS Symbol Parameter t Write Cycle Time Write End t SCE t Address Setup Time to AW Write End t Address Hold from HA Write End t Address Setup Time SA WE Pulse Width (OE High) t (1) PWE 1 WE Pulse Width (OE Low) t (2) PWE ...
Page 8
... IS63LV1024 IS63LV1024L AC WAVEFORMS (1) (WE Controlled HIGH during Write Cycle) WRITE CYCLE NO. 2 ADDRESS OE CE LOW DATA UNDEFINED OUT D IN (WE Controlled LOW During Write Cycle) WRITE CYCLE NO. 3 ADDRESS OE LOW CE LOW DATA UNDEFINED OUT D IN Notes: 1. The internal write time is defined by the overlap of CE LOW and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to terminate the Write ...
Page 9
... GND Integrated Silicon Solution, Inc. — www.issi.com — Rev. K 6/11/08 Test Condition Options See Data Retention Waveform = 2.0V – 0.2V IS63LV1024 DD DD IS63LV1024L See Data Retention Waveform See Data Retention Waveform = 3.0V and not 100% tested (CE Controlled) Data Retention Mode SDR 0.2V ...
Page 10
... IS63LV1024 IS63LV1024L IS63LV1024 ORDERING INFORMATION Commercial Range: 0°C to +70°C Speed (ns) Order Part No. 8 IS63LV1024-8K IS63LV1024-8KL 10 IS63LV1024-10T IS63LV1024-10J IS63LV1024-10K 12 IS63LV1024-12T IS63LV1024-12J IS63LV1024-12KL Industrial Range: –40°C to +85°C Speed (ns) Order Part No. 8 IS63LV1024-8KI 10 IS63LV1024-10KI 12 IS63LV1024-12TI 10 Package 400-mil Plastic SOJ 400-mil Plastic SOJ, Lead-free ...
Page 11
... IS63LV1024 IS63LV1024L IS63LV1024L ORDERING INFORMATION Commercial Range: 0°C to +70°C Speed (ns) Order Part No. 8 IS63LV1024L-8T IS63LV1024L-8TL IS63LV1024L-8B 10 IS63LV1024L-10T IS63LV1024L-10TL IS63LV1024L-10HL 12 IS63LV1024L-12T IS63LV1024L-12H IS63LV1024L-12J IS63LV1024L-12JL IS63LV1024L-12B Industrial Range: –40°C to +85°C Speed (ns) Order Part No. 8 IS63LV1024L-8TI IS63LV1024L-8JI IS63LV1024L-8KI IS63LV1024L-8BI 10 IS63LV1024L-10HI IS63LV1024L-10JLI ...
Page 12
... BSC Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — ...
Page 13
... BSC Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products ...
Page 14
... BSC Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — ...
Page 15
... B 0.66 — 0.010 C 0.20 — 0.730 D 20.83 — 0.345 E 8.26 — 0.305 E1 7.49 — 0.287 E2 6.27 e 1.27 BSC Integrated Silicon Solution, Inc. — www.issi.com — INCHES Min. Typ. Max. 32 — 3.56 — — 0.140 — — 0.025 — — — 2.67 0.095 — 0.105 — 0.51 0.016 — 0.020 — ...
Page 16
... D 13.20 13.60 D1 11.70 11.90 E 7.90 8.10 e 0.50 BSC L 0.30 0.70 S 0.28 Typ. 0° 5° Integrated Silicon Solution, Inc. PK13197H32 Rev. B 04/21/ Inches Min Max Notes: 1. Controlling dimension: millimeters, unless otherwise specified. 2. BSC = Basic lead spacing between centers. 3. Dimensions D1 and E do not include mold flash protru- — 0.049 sions and should be measured from the bottom of the package ...
Page 17
... Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — ...
Page 18
... Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — ...