MT90826 Mitel Networks Corporation, MT90826 Datasheet - Page 6

• Manufacturer Part Number: MT90826
• Description: Quad Digital Switch
• Manufacturer: Mitel Networks Corporation

MT90826
Device Overview
The MT90826 Quad Digital Switch is capable of
switching up to 4,096
MT90826 is designed to switch 64 kbit/s PCM or N x
64k bit/s data. The device maintains frame integrity
in data applications and minimum throughput delay
for voice applications on a per channel basis.
The serial input streams of the MT90826 can have a
bit rate of 2.048, 4.096, 8.192 or 16.384 Mbit/s and
are arranged in 125 s wide frames, which contain
32, 64,128 or 256 channels, respectively. The data
rates on input and output streams match. All inputs
and outputs may be programmed to 2.048, 4.096 or
8.192 Mb/s. STi0-15 and STo0-15 may be set to
16.384 Mb/s. Combinations of two bit rates, N and
2N are provided. See Table 1.
By using Mitel’s message mode capability, the
microprocessor
timeslots on a per channel basis. This feature is
useful for transferring control and status information
for external circuits or other ST-BUS devices.
The frame offset calibration function allows users to
measure the frame offset delay for streams STi0 to
STi31. The offset calibration is activated by a frame
evaluation bit in the frame evaluation register. The
evaluation result is stored in the frame evaluation
registers and can be used to program the input offset
delay for individual streams using internal frame
input offset registers.
6
Serial Interface Mode
16 Mb/s and 8 Mb/s
4 Mb/s and 8 Mb/s
2 Mb/s and 4 Mb/s
16 Mb/s
8 Mb/s
4 Mb/s
2 Mb/s
can
CMOS
access
Table 1 - Stream Usage and External Clock Rates
4,096 channels. The
Input Stream
input
STi15-31
STi12-19
STi16-31
STi0-31
STi0-15
STi0-15
STi0-11
STi0-31
STi0-15
STi0-31
and
output
Input Data Rate
16 Mb/s
16 Mb/s
8 Mb/s
4 Mbs/
8 Mb/s
8 Mb/s
4 Mb/s
2 Mb/s
4 Mb/s
2 Mb/s
The microport interface is compatible with Motorola
non-multiplexed
locations may be directly written to or read from; data
memory locations may be directly read from. A DTA
signal is provided to hold the bus until the
asynchronous microport operation is queued into the
device. For applications that require no wait states,
indirect
Intermediary registers are directly programmed with
the write data and address, or read address. The
data in the intermediary registers is internally
transferred synchronous with the operation of the
internal state machines. Completion of the operation
is indicated by a status register flag.
Functional Description
A functional Block Diagram of the MT90826 is shown
in Figure 1.
Data and Connection Memory
For all data rates, the received serial data is
converted to parallel format by internal serial-to-
parallel converters and stored sequentially in the
data
operation programmed in the control register, the
usable data memory may be as large as 4,096 bytes.
The sequential addressing of the data memory is
performed by an internal counter, which is reset by
the input 8 kHz frame pulse (F0i) to mark the frame
boundaries of the incoming serial data streams.
Data to be output on the serial streams may come
from either the data memory or connection memory.
memory.
reading
Output Stream
STo16-31
STo12-19
STo16-31
STo0-31
STo0-15
STo0-15
STo0-11
STo0-31
STo0-15
STo0-31
Depending
buses.
and
Advanced Information
writing
Connection
upon
Output Data Rate
may
16 Mb/s
16 Mb/s
8 Mb/s
4 Mb/s
8 Mb/s
8 Mb/s
4 Mb/s
2 Mb/s
4 Mb/s
2 Mb/s
the
be
selected
memory
used.