IDT5T2010 Integrated Device Technology, IDT5T2010 Datasheet - Page 10

• Manufacturer Part Number: IDT5T2010
• Description: 2.5v Zero Delay Pll Clock Driver Teraclock
• Manufacturer: Integrated Device Technology

POWER SUPPLY CHARACTERISTICS FOR eHSTL OUTPUTS
NOTES:
1. These power consumption characteristics are for all the valid input interfaces and cover the worst case input and output interface combinations.
2. The termination resistors are excluded from these measurements.
3. If the differential input interface is used, the true input is held LOW and the complementary input is held HIGH.
4. FS = HIGH.
DIFFERENTIAL INPUT AC TEST CONDITIONS FOR eHSTL
NOTES:
1. The 1V peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the V
2. A 900mV crossing point level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the V
3. In all cases, input waveform timing is marked at the differential cross-point of the input signals.
4. The input signal edge rate of 1V/ns or greater is to be maintained in the 20% to 80% range of the input waveform.
IDT5T2010
2.5V ZERO DELAY PLL CLOCK DRIVER TERACLOCK
Symbol
Symbol
specification under actual use conditions.
actual use conditions.
I
I
I
I
I
DDQQ
I
DDDQ
DDPD
I
TOTQ
t
V
V
DDQ
DDD
TOT
R
V
DIF
THI
, t
X
F
Quiescent V
Quiescent V
Power Down Current
Dynamic V
Current per Output
Dynamic V
Current per Output
Total Power V
Total Power V
Parameter
Input Signal Swing
Differential Input Signal Crossing Point
Input Timing Measurement Reference Level
Input Signal Edge Rate
DDQ
Parameter
DD
DD
DDQ
DD
DDQ
Power Supply
Power Supply Current
Power Supply
Power Supply Current
Supply Current
Supply Current
(1)
(4)
(4)
(4)
(3)
(3)
(2)
V
PLL_EN = HIGH, DS
FBF
V
PLL_EN = HIGH, DS
FBF
V
V
V
V
V
V
V
DDQ
DDQ
DD
DD
DD
DDQ
DDQ
DDQ
DDQ
(3)
[2:1]
[2:1]
= Max., PD = LOW, nSOE = LOW, PLL_EN = HIGH
= Max., V
= Max., V
= 1.8V, F
= 1.8V, F
= 1.8V, F
= 1.8V, F
= Max., REF = LOW, PD = HIGH, nSOE = LOW,
= Max., REF = LOW, PD = HIGH, nSOE = LOW,
= LH, Outputs enabled, All outputs unloaded
= LH, Outputs enabled, All outputs unloaded
Test Conditions
DDQ
DDQ
VCO
VCO
VCO
VCO
= Max., C
= Max., C
= 100MHz, C
= 250MHz, C
= 100MHz, C
= 250MHz, C
10
[1:0]
[1:0]
= MM, nF
= MM, nF
(2)
L
L
= 0pF
= 0pF
L
L
L
L
= 15pF
= 15pF
= 15pF
= 15pF
[2:1]
[2:1]
= LH,
= LH,
INDUSTRIAL TEMPERATURE RANGE
(1)
Crossing Point
Typ.
115
1.7
0.8
15
13
20
35
55
50
Value
900
1
1
Max
175
25
50
20
30
55
85
75
3
X
specification under
Units
V/ns
mV
V
V
A/MHz
A/MHz
Unit
mA
mA
mA
mA
A
DIF
(AC)