UPD784035YGC NEC, UPD784035YGC Datasheet - Page 92
UPD784035YGC
Manufacturer Part Number
UPD784035YGC
Description
16-/8-BIT SINGLE-CHIP MICROCONTROLLERS
Manufacturer
NEC
Datasheet
1.UPD784035YGC.pdf
(94 pages)
- Current page: 92 of 94
- Download datasheet (504Kb)
92
1 PRECAUTION AGAINST ESD FOR SEMICONDUCTORS
2 HANDLING OF UNUSED INPUT PINS FOR CMOS
3 STATUS BEFORE INITIALIZATION OF MOS DEVICES
Note: Strong electric field, when exposed to a MOS device, can cause destruction of
Note: No connection for CMOS device inputs can be cause of malfunction. If no
Note: Power-on does not necessarily define initial status of MOS device. Production
the gate oxide and ultimately degrade the device operation. Steps must be
taken to stop generation of static electricity as much as possible, and quickly
dissipate it once, when it has occurred.
adequate. When it is dry, humidifier should be used. It is recommended to avoid
using insulators that easily build static electricity. Semiconductor devices
must be stored and transported in an anti-static container, static shielding bag
or conductive material. All test and measurement tools including work bench
and floor should be grounded. The operator should be grounded using wrist
strap. Semiconductor devices must not be touched with bare hands. Similar
precautions need to be taken for PW boards with semiconductor devices on it.
connection is provided to the input pins, it is possible that an internal input level
may be generated due to noise, etc., hence causing malfunction. CMOS device
behave differently than Bipolar or NMOS devices. Input levels of CMOS devices
must be fixed high or low by using a pull-up or pull-down circuitry. Each unused
pin should be connected to V
a possibility of being an output pin. All handling related to the unused pins must
be judged device by device and related specifications governing the devices.
process of MOS does not define the initial operation status of the device.
Immediately after the power source is turned ON, the devices with reset function
have not yet been initialized. Hence, power-on does not guarantee out-pin
levels, I/O settings or contents of registers. Device is not initialized until the
reset signal is received. Reset operation must be executed immediately after
power-on for devices having reset function.
NOTES FOR CMOS DEVICES
DD
or GND with a resistor, if it is considered to have
PD784035Y, 784036Y, 784037Y, 784038Y
Environmental control must be
Related parts for UPD784035YGC
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
8BIT MCU, 60K FLASH, 3KB RAM, LQFP
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
8BIT MCU, 128K FLASH, 7KB RAM, SMD
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
8BIT MCU, 4K FLASH, 256B RAM, 78F9222
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
8BIT MCU, 4K FLASH, 128B RAM, 78F9212
Manufacturer:
NEC
Part Number:
Description:
16/8 bit single-chip microcomputer
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual audio power amp circuit
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual comparator
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
MOS type composite field effect transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
50 V/100 mA FET array incorporating 2 N-ch MOSFETs
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet: