sak-xc2766x-96f66l-ac Infineon Technologies Corporation, sak-xc2766x-96f66l-ac Datasheet - Page 74

• Manufacturer Part Number: sak-xc2766x-96f66l-ac
• Description: 16/32-bit Single-chip Microcontroller With 32-bit Performance
• Manufacturer: Infineon Technologies Corporation

Preliminary
Table 14
Parameter
XTAL1 input current
Pin capacitance
(digital inputs/outputs)
1) Keeping signal levels within the limits specified in this table ensures operation without overload conditions. For
2) Overload conditions must not occur on pin XTAL1.
3) Not subject to production test - verified by design/characterization. Hysteresis is implemented to avoid
4) The maximum deliverable output current of a port driver depends on the selected output driver mode, see
5) As a rule, with decreasing output current the output levels approach the respective supply level (
6) This specification is not valid for outputs which are switched to open drain mode. In this case the respective
7) An additional error current (
8) The given values are worst-case values. In production test, this leakage current is only tested at 125°C; other
9) Keep current: Limit the current through this pin to the indicated value so that the enabled pull device can keep
10) Not subject to production test - verified by design/characterization.
Data Sheet
signal levels outside these specifications, also refer to the specification of the overload current
metastable states and switching due to internal ground bounce. It cannot suppress switching due to external
system noise under all conditions.
Table
V
output will float and the voltage is determined by the external circuit.
the definition of the overload coupling factor
values are ensured by correlation. For derating, please refer to the following descriptions:
Leakage derating depending on temperature (
I
Leakage derating depending on voltage level (DV =
I
This voltage derating formula is an approximation which applies for maximum temperature.
Because pin P2.8 is connected to two pads (standard pad and high-speed clock pad), it has twice the normal
leakage.
the default pin level:
Force current: Drive the indicated minimum current through this pin to change the default pin level driven by
the enabled pull device:
These values apply to the fixed pull-devices in dedicated pins and to the user-selectable pull-devices in
general purpose IO pins.
Because pin P2.8 is connected to two pads (standard pad and high-speed clock pad), it has twice the normal
capacitance.
OZ
OZ
OH
= 0.009 × e
=
→
I
V
OZtempmax
13,
DDP
Current Limits for Port Output
). However, only the levels for nominal output currents are verified.
DC Characteristics for Upper Voltage Range (cont’d)
(Operating Conditions apply)
(0.054×TJ)
- (1.6 × DV) [µA]
10)
V
PIN
[µA]. For example, at a temperature of 130°C the resulting leakage current is 10.07 µA.
V
≥
PIN
V
I
INJ
OH
≤
) will flow if an overload current flows through an adjacent pin. Please refer to
V
for a pullup;
Symbol
I
C
IL
IL
IO
for a pullup;
CC
CC
Drivers. The limit for pin groups must be respected.
V
K
Min.
–
–
PIN
OV
T
V
J
.
PIN
= junction temperature [°C]):
≤
V
72
≥
V
IL
V
DDP
for a pulldown.
1)
IH
Values
Typ.
–
–
for a pulldown.
-
V
PIN
[V]):
Max.
±20
10
XC2000 Family Derivatives
Unit Note /
µA
pF
Electrical Parameters
Test Condition
0 V <
V2.0, 2008-03
V
XC2766X
I
OV
IN
.
<
V
OL
V
→
DDI
V
SS
,