ICL7106_0512 INTERSIL [Intersil Corporation], ICL7106_0512 Datasheet
ICL7106_0512
Related parts for ICL7106_0512
ICL7106_0512 Summary of contents
Page 1
Data Sheet Digit, LCD/LED Display, A/D 2 Converters The Intersil ICL7106 and ICL7107 are high performance, low 1 power digit A/D converters. Included are seven 2 segment decoders, display drivers, a reference, and a ...
Page 2
Pinouts ICL7106, ICL7107 (PDIP) TOP VIEW (1’ (10’ ...
Page 3
Absolute Maximum Ratings Supply Voltage ICL7106 ...
Page 4
Electrical Specifications (Note 3) (Continued) PARAMETER DISPLAY DRIVER ICL7107 ONLY Segment Sinking Current Except Pins AB4 and POL Pin AB4 Only Pin POL Only NOTES: 3. Unless otherwise noted, specifications apply to both the ICL7106 and ICL7107 ...
Page 5
Design Information Summary Sheet • OSCILLATOR FREQUENCY f = 0.45/RC OSC C > 50pF; R > 50kΩ OSC OSC f (Typ) = 48kHz OSC • OSCILLATOR PERIOD t = RC/0.45 OSC • INTEGRATION CLOCK FREQUENCY CLOCK ...
Page 6
Detailed Description Analog Section Figure 3 shows the Analog Section for the ICL7106 and ICL7107. Each measurement cycle is divided into three phases. They are (1) auto-zero (A-Z), (2) signal integrate (INT) and (3) de-integrate (DE). Auto-Zero Phase During auto-zero ...
Page 7
Analog COMMON This pin is included primarily to set the common mode voltage for battery operation (ICL7106) or for any system where the input signals are floating with respect to the power supply. The COMMON pin sets a voltage that ...
Page 8
V+ BP ICL7106 DECIMAL POINT SELECT TEST CD4030 FIGURE 6. EXCLUSIVE ‘OR’ GATE FOR DECIMAL POINT DRIVE Digital Section Figures 7 and 8 show the digital section for the ICL7106 and ICL7107, respectively. In the ICL7106, an internal digital ground ...
Page 9
TYPICAL SEGMENT OUTPUT V+ 0.5mA TO SEGMENT 8mA DIGITAL GROUND † THREE INVERTERS ONE INVERTER SHOWN FOR CLARITY OSC 1 System Timing Figure 9 shows the clocking arrangement used in the ICL7106 and ICL7107. Two basic clocking arrangements can be ...
Page 10
Component Value Selection Integrating Resistor Both the buffer amplifier and the integrator have a class A output stage with 100µA of quiescent current. They can supply 4µA of drive current with negligible nonlinearity. The integrating resistor should be large enough ...
Page 11
Typical Applications The ICL7106 and ICL7107 may be used in a wide variety of configurations. The circuits which follow show some of the possibilities, and serve to illustrate the exceptional versatility of these A/D converters. The following application notes contain ...
Page 12
Typical Applications (Continued) TO PIN 1 OSC 1 40 100kΩ OSC 2 39 OSC 3 38 100pF TEST 37 REF HI 36 REF LO 35 1kΩ REF 0.1µ REF COMMON ...
Page 13
Typical Applications (Continued) TO PIN 1 OSC 1 40 100kΩ OSC 2 39 OSC 3 38 100pF TEST 37 REF HI 36 REF REF 0.1µ REF COMMON ...
Page 14
Typical Applications (Continued) TO PIN 1 OSC 1 40 100kΩ OSC 2 39 OSC 3 38 100pF TEST 37 REF HI 36 REF REF 0.1µ REF COMMON ...
Page 15
Dual-In-Line Plastic Packages (PDIP INDEX N/2 AREA -B- -A- D BASE PLANE -C- SEATING PLANE 0.010 (0.25 NOTES: 1. Controlling Dimensions: INCH. In case of conflict between ...
Page 16
Metric Plastic Quad Flatpack Packages (MQFP -D- - PIN 1 - -16 0.40 0.20 0.016 MIN 0.008 o 0 MIN 0.13/0.17 0.005/0.007 -16 L ...