CY8C36_1105 CYPRESS [Cypress Semiconductor], CY8C36_1105 Datasheet - Page 24

• Manufacturer Part Number: CY8C36_1105
• Description: Programmable System-on-Chip (PSoC) Multiply and divide instructions
• Manufacturer: CYPRESS [Cypress Semiconductor]

I/O Port SFRs
The I/O ports provide digital input sensing, output drive, pin
interrupts, connectivity for analog inputs and outputs, LCD, and
access to peripherals through the DSI. Full information on I/O
ports is found in
I/O ports are linked to the CPU through the PHUB and are also
available in the SFRs. Using the SFRs allows faster access to a
limited set of I/O port registers, while using the PHUB allows boot
configuration and access to all I/O port registers.
Each SFR supported I/O port provides three SFRs:
5.7.3.1 xdata Space
The 8051 xdata space is 24-bit, or 16 MB in size. The majority of
this space is not “external”—it is used by on-chip components.
See
accessed using the EMIF. See
page 22.
Document Number: 001-53413 Rev. *L
SFRPRTxDR sets the output data state of the port (where × is
port number and includes ports 0–6, 12 and 15).
The SFRPRTxSEL selects whether the PHUB PRTxDR
register or the SFRPRTxDR controls each pin’s output buffer
within the port. If a SFRPRTxSEL[y] bit is high, the
corresponding SFRPRTxDR[y] bit sets the output state for that
pin. If a SFRPRTxSEL[y] bit is low, the corresponding
PRTxDR[y] bit sets the output state of the pin (where y varies
from 0 to 7).
The SFRPRTxPS is a read only register that contains pin state
values of the port pins.
Table
5-5. External, that is, off-chip, memory can be
I/O System and Routing
External Memory Interface
on page 32.
on
Table 5-5. XDATA Data Address Map
0×00 0000 – 0×00 1FFF
0×00 4000 – 0×00 42FF
0×00 4300 – 0×00 43FF
0×00 4400 – 0×00 44FF
0×00 4500 – 0×00 45FF
0×00 4700 – 0×00 47FF
0×00 4900 – 0×00 49FF
0×00 4E00 – 0×00 4EFF
0×00 4F00 – 0×00 4FFF
0×00 5000 – 0×00 51FF
0×00 5400 – 0×00 54FF
0×00 5800 – 0×00 5FFF
0×00 6000 – 0×00 60FF
0×00 6400 – 0×00 6FFF
0×00 7000 – 0×00 7FFF
0×00 8000 – 0×00 8FFF
0×00 A000 – 0×00 A400
0×00 C000 – 0×00 C800
0×01 0000 – 0×01 FFFF
0×05 0220 – 0×05 02F0
0×08 0000 – 0×08 1FFF
0×80 0000 – 0×FF FFFF
Address Range
PSoC
®
SRAM
Clocking, PLLs, and oscillators
Power management
Interrupt controller
Ports interrupt control
Flash programming interface
I
Decimator
Fixed timer/counter/PWMs
I/O ports control
External Memory Interface
(EMIF) control registers
Analog Subsystem interface
USB controller
UDB configuration
PHUB configuration
EEPROM
CAN
Digital Filter Block
Digital Interconnect
configuration
Debug controller
flash ECC bytes
External Memory Interface
2
C controller
3: CY8C36 Family
Purpose
Data Sheet
Page 24 of 126