HA16341FP HITACHI [Hitachi Semiconductor], HA16341FP Datasheet
HA16341FP
Related parts for HA16341FP
HA16341FP Summary of contents
Page 1
HA16341NT/FP, HA16342NT/FP Redundant Secondary Switching Power Supply Controller Description The HA16341NT/FP and the HA16342NT/FP are switching regulator control ICs for the off-line converters of redundant power supplies. The HA16342NT/FP is reverse current detection less version of the HA16341NT/FP. The HA16341NT/FP ...
Page 2
... Cin 19 EOUT SGND PGND TAB PGND PGND 18 MF OUT 17 VCC PG1 16 MR OUT FAIL 15 PWM OUT Trig 14 HSP CT 13 Vref SS DB HA16341FP, HA16342FP (FP-26DT CF(+) 2 25 CF(− CFo 4 23 CFB 5 22 EIN 6 21 EOUT 7 20 PGND TAB TAB PGND ...
Page 3
Pin Functions Pin No. DP-24TS FP-26DT ...
Page 4
HA16341NT/FP, HA16342NT/FP Block Diagram Current share input CS(+) + OP1 − Point B CS(− OP1-2 − 26dB 19R MT OCL + CB OP3 − Cin + 6dB OP2 − R SGND R S RS-FF latch A S2 PG1 ...
Page 5
Absolute Maximum Ratings (Ta = 25°C) Item Supply Voltage DC output current1 Peak output current1 DC output current2 Peak output current2 DC output current3 Peak output current3 DC output current4 DC output current5 DC output current6 DC output current7 Peak ...
Page 6
... This is allowable value 25°C. Derate by θj-a = 30°C/W above that temperature. θj-a = 30°C/W is the case that HA16341NT is mounted on 30% wiring density glass epoxy board (105 mm × 76.2 mm × 1.6 mmt) and HA16341FP is mounted on a board which thermal resistance is 23°C/W because of θj-pin (SOP) = 7°C/W typ. 5.0 4 ...
Page 7
Electrical Characteristics (Ta = 25° 12V, PG1 = 3V, Vtrig = 0V, VCS(+) = 0V, VCin = 0V, CCT = 330pF, GvOP1 = 26dB, CC GvOP4 = 40dB, RDB = 1.8kΩ) • Current share Item Symbol CB output ...
Page 8
HA16341NT/FP, HA16342NT/FP Electrical Characteristics (cont.) (Ta = 25° 12V, PG1 = 3V, Vtrig = 0V, VCS(+) = 0V, VCin = 0V, CCT = 330pF, GvOP1 = 26dB, CC GvOP4 = 40dB, RDB = 1.8kΩ) • Oscillator Item Symbol ...
Page 9
Electrical Characteristics (cont.) (Ta = 25° 12V, PG1 = 3V, Vtrig = 0V, VCS(+) = 0V, VCin = 0V, CCT = 330pF, GvOP1 = 26dB, CC GvOP4 = 40dB, RDB = 1.8kΩ) • PG1 Item Symbol PG1 threshold ...
Page 10
HA16341NT/FP, HA16342NT/FP Electrical Characteristics (cont.) (Ta = 25° 12V, PG1 = 3V, Vtrig = 0V, VCS(+) = 0V, VCin = 0V, CCT = 330pF, GvOP1 = 26dB, CC GvOP4 = 40dB, RDB = 1.8kΩ) • MR OUT Item ...
Page 11
Electrical Characteristics (cont.) (Ta = 25° 12V, PG1 = 3V, Vtrig = 0V, VCS(+) = 0V, VCin = 0V, CCT = 330pF, GvOP1 = 26dB, CC GvOP4 = 40dB, RDB = 1.8kΩ) • SS Item Symbol SS sink ...
Page 12
HA16341NT/FP, HA16342NT/FP Timing Chart 1 (Total) VCC 0V Vref (5V typ PG1 3V (by switch) 0V UVL2 (internal Vth : 3.4V typ CTH CT Vth : 1.3V typ CTL 0V OUT (PWM) 0V 1.25V (100%) ...
Page 13
Timing Chart 2 (Hot Swap) Vref 0V 3V PG1 0V Internal latch signal (inverting) (OVP, OCL or Reverse current) : Node S1 in Block Diagram 0V UVL2 (internal) 0V 1.25V (100%) 1.187V (95%) EIN 0V Internal latch signal : Node ...
Page 14
HA16341NT/FP, HA16342NT/FP Timing Chart 3 (Dead Band Control) CT PWM OUT MR OUT MF OUT Td1 Note: V determines maximum duty. This waveform example shows the case of EIN = Lo Voltage of SS pin SS Vref ...
Page 15
Timing Chart 4 (Soft Start) Vth : 3.4V CTH Note * CT SS Vth : 1.3V CTL OUT (PWM) Note: Self-oscillation: Vth CTH Synchronized operation: Vth ≥ Vth Case V HSS CTH Maximum duty would be the value specified in ...
Page 16
HA16341NT/FP, HA16342NT/FP Timing Chart 5 (External Trigger Control) Primary IC oscillation 0V Primary IC AUX-OUT 0V Trigger input (Trig terminal) 0V Trigger Vth Vtrig: −0.5V typ Trigger detector internal signal 0V Secondary oscillation 0V This IC is triggered by negative ...
Page 17
Timing Chart 6 (Duty Control) CT OP1-2 (internal) 300mV 1/3×(EOUT− (internal) OUT (PWM) CT CT' = 5.33 The amplitude of CT' is 300mV typ at synchronous operation with trigger frequency as 200kHz and C 1.3 1.24 ...
Page 18
HA16341NT/FP, HA16342NT/FP Timing Chart 7 (Current Limitting) 1/3×(EOUT− 1.24V clamped BE (internal) CT OP1-2 (internal) 300mV OUT (PWM) CT CT' = 5.33 The amplitude of CT' is 300mV typ at synchronous operation with trigger frequency as ...
Page 19
Timing Chart 8 (Interface with Primary Control IC) Vref PG1 (from primary IC) Internal latch signal (inverting) (OVP, OCL or Reverse current) : Node S1 in Block Diagram UVL2 (internal signal) OUT (PWM) FAIL (to primary IC) Note: Reverse current ...
Page 20
HA16341NT/FP, HA16342NT/FP Package Dimensions 24 1 1.5 Max 1.78 ± 0.25 18.4 19.2 Max 26 1 1.20 Max 0.80 2.8 3.6 *0.37 ± 0.08 0.35 ± 0.06 *Dimension including the plating thickness Base material dimension Rev.1, Jan. 2001, page 20 ...
Page 21
Disclaimer 1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent, copyright, trademark, or other intellectual property rights for information contained in this document. Hitachi bears no responsibility for problems that may arise ...