ISL85001IRZ Intersil, ISL85001IRZ Datasheet - Page 10

• Manufacturer Part Number: ISL85001IRZ
• Description: IC REG PWM BUCK 1A 12-DFN
• Manufacturer: Intersil
• Type: Step-Down (Buck), PWM - Voltage Moder

Specifications of ISL85001IRZ

• Internal Switch(s): Yes
• Synchronous Rectifier: No
• Number Of Outputs: 1
• Voltage - Output: 0.6 ~ 19 V
• Current - Output: 1A
• Frequency - Switching: 500kHz
• Voltage - Input: 4.5 ~ 25 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: *
• Package / Case: 12-DFN
• Voltage - Supply: 4.5 V ~ 25 V
• Frequency-max: 550kHz
• Duty Cycle: 80%
• Pwm Type: Voltage Mode
• Buck: Yes
• Boost: No
• Flyback: No
• Inverting: No
• Doubler: No
• Divider: No
• Cuk: No
• Isolated: No
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Detailed Description
The ISL85001 combines a standard buck PWM controller
with an integrated switching MOSFET. The buck controller
drives an internal N-Channel MOSFET and requires an
external diode to deliver load current up to 1A. A Schottky
diode is recommended for improved efficiency and
performance over a standard diode. The standard buck
regulator can operate from either an unregulated DC source,
such as a battery, with a voltage ranging from +5.5V to +25V,
or from a regulated system rail of +5V. When operating from
+5.5V or greater, the controller is biased from an internal
+5V LDO voltage regulator. The converter output is
regulated down to 0.6V from either input source. These
features make the ISL85001 ideally suited for FPGA and
wireless chipset power applications.
The PWM control loop uses a single output voltage loop with
input voltage feed forward, which simplifies feedback loop
compensation and rejects input voltage variation. External
feedback loop compensation allows flexibility in output filter
component selection. The regulator switches at a fixed 500kHz.
The buck regulator is equipped with a lossless current limit
scheme. The current limit in the buck regulator is achieved
by monitoring the drain-to-source voltage drop of the internal
switching power MOSFET. The current limit threshold is
internally set at 1.7A. The part also features undervoltage
protection by latching the switching MOSFET driver to the
OFF-state during an overcurrent, when the output voltage is
lower than 70% of the regulated output. This helps minimize
power dissipation during a short-circuit condition. Due to
only the switching power MOSFET integration, there is no
overvoltage protection feature for this part.
+5V Internal Bias Supply (VDD)
Voltage applied to the VIN pin with respect to GND is
regulated to +5V DC by an internal LDO regulator. The output
of the LDO, VDD, is the bias voltage used by all the internal
control and protection circuitry. The VDD pin requires a
ceramic capacitor connected to GND. The capacitor serves to
stabilize the LDO and to decouple load transients.
The input voltage range for the ISL85001 is specified as
+5.5V to +25V or +5V ±10%. In the case of an unregulated
supply case, the power supply is connected to VIN only.
Once enabled, the linear regulator will turn-on and rise to
+5V on VDD. In the +5V supply case, the VDD and VIN pins
must be tied together to bypass the LDO. The external
decoupling capacitor is still required in this mode.
Operation Initialization
The power-on reset circuitry and enable inputs prevent false
start-up of the PWM regulator output. Once all the input
criteria are met, the controller soft-starts the output voltage
to the programmed level.
10
ISL85001
Power-On Reset and Undervoltage Lockout
The PWM portion of the ISL85001 automatically initializes
upon receipt of input power. The power-on reset (POR)
function continually monitors the VDD voltage. While below
the POR thresholds, the controller inhibits switching off the
internal power MOSFET. Once exceeded, the controller
initializes the internal soft-start circuitry. If either input supply
drops below their falling POR threshold during soft-start or
operation, the buck regulator latches off.
Enable and Disable
All internal power devices are held in a high-impedance
state, which ensures they remain off while in shutdown
mode. Typically, the enable input for a specific output is
toggled high after the input supply to that regulator is active
and the internal LDO has exceeded it’s POR threshold.
The EN pin enables the buck controller portion of the
ISL85001. When the voltage on the EN pin exceeds the
POR rising threshold, the controller initiates the soft-start
function for the PWM regulator. If the voltage on the EN pin
drops below the POR falling threshold, the buck regulator
shuts down.
Pulling the EN pin low simultaneously put the output into
shutdown mode and supply current drops to 100µA typical.
Soft-Start
Once the input supply latch and enable threshold are met, the
soft-start function is initialized. The soft-start circuitry begins
sourcing 30µA, from an internal current source, which
charges the external soft-start capacitor. The voltage on SS
begins ramping linearly from ground until the voltage across
the soft-start capacitor reaches 3.0V. This linear ramp is
applied to the non-inverting input of the internal error amplifier
and overrides the nominal 0.6V reference. The output voltage
reaches its regulation value when the soft-start capacitor
voltage reaches 1.6V. Connect a capacitor from SS pin to
ground. This capacitor (along with an internal 30µA current
source) sets the soft-start interval of the converter, t
Upon disable, the SS pin voltage will discharge to zero voltage.
Power-Good
PG is an open-drain output of a window comparator that
continuously monitors the buck regulator output voltage. PG is
actively held low when EN is low and during the buck regulator
soft-start period. After the soft-start period terminates, PG
becomes high impedance as long as the output voltage is
within ±12% of the nominal regulation voltage set by FB. When
VOUT drops 12% below or rises 12% above the nominal
regulation voltage, the ISL85001 pulls PG low. Any fault
condition forces PG low until the fault condition is cleared by
attempts to soft-start. For logic level output voltages, connect
an external pull-up resistor between PG and VDD. A 100kΩ
resistor works well in most applications.
C
SS
[
μF
]
=
50 t
⋅
SS
s [ ]
March 17, 2009
SS
.
(EQ. 1)
FN6769.1