ISL6564AIRZ Intersil, ISL6564AIRZ Datasheet - Page 20

• Manufacturer Part Number: ISL6564AIRZ
• Description: IC CTRLR PWM MULTIPHASE 40-QFN
• Manufacturer: Intersil

Specifications of ISL6564AIRZ

• Pwm Type: Voltage Mode
• Number Of Outputs: 1
• Frequency - Max: 1.5MHz
• Duty Cycle: 66.7%
• Voltage - Supply: 4.75 V ~ 5.25 V
• Buck: Yes
• Boost: No
• Flyback: No
• Inverting: No
• Doubler: No
• Divider: No
• Cuk: No
• Isolated: No
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-VFQFN, 40-VFQFPN
• Frequency-max: 1.5MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

At the beginning of overcurrent shutdown, the controller
places all PWM signals in a high-impedance state within
20ns commanding the Intersil MOSFET driver ICs to turn off
both upper and lower MOSFETs. The system remains in this
state a period of 4096 switching cycles. If the controller is still
enabled at the end of this wait period, it will attempt a
soft-start. If the fault remains, the trip-retry cycles will
continue indefinitely (as shown in Figure 13) until either
controller is disabled or the fault is cleared. Note that the
energy delivered during trip-retry cycling is much less than
during full-load operation, so there, there is no thermal
hazard during this kind of operation.
Driver Enable Output
The ISL6564A has a driver enable output pin DRVEN. The
DRVEN is designed for the application where ISL6564A
needs to work with drivers that can not recognize three-state
PWM input.
FIGURE 13. OVERCURRENT BEHAVIOR IN HICCUP MODE,
0A
0V
FIGURE 14. DRVEN WAVEFORM AT START-UP
OUTPUT CURRENT, 50A/DIV
OUTPUT VOLTAGE,
500mV/DIV
F
SW
= 500kHz
2ms/DIV
500µs/DIV
20
DRVEN, 5V/DIV
VOUT, 1V/DIV
EN, 5V/DIV
ISL6564A
In normal operation, DRVEN remains low until ISL6564A
begins soft-start ramp and then changes to high (Figure 14).
When an overcurrent event occurs, DRVEN is pulled to low
instantly (less than 20ns) to disable the driver so that both
upper and lower FETs be turned off (Figure 15). During an
overvoltage condition, DRVEN remains high to allow the
driver turn on the lower FETs based on the PWM input to
discharge the energy stored in the output inductor. Once the
Output voltage is reduced to 0.6V, DRVEN is pulled to low as
shown in Figure 16.
There’s no need to use DRVEN when ISL6564A is used to
work with Intersil’s drivers such as ISL6612 and ISL6605.
Current Sense Output
The ISL6564A has 2 current sense output pins IDROOP and
IOUT. They are identical. In typical application, IDROOP pin
is connected to FB pin for the application where load line is
required. IOUT pin was designed for load current
measurement. As shown in typical application schematics
FIGURE 15. DRVEN DURING OVERCURRENT OPERATION
FIGURE 16. DRVEN DURING OVERCURRENT OPERATION
0A
0V
0V
OUTPUT CURRENT, 50A/DIV
OUTPUT VOLTAGE,
500mV/DIV
DRVEN, 5V/DIV
DRVEN, 5V/DIV
OUTPUT VOLTAGE,
500mV/DIV
2ms/DIV
2ms/DIV
March 20, 2007
FN6285.1