BD9775FV-E2 Rohm Semiconductor, BD9775FV-E2 Datasheet - Page 21

• Manufacturer Part Number: BD9775FV-E2
• Description: IC REG SW STEP DOWN HE 28-SSOP
• Manufacturer: Rohm Semiconductor
• Type: Step-Down (Buck)r

Specifications of BD9775FV-E2

• Internal Switch(s): No
• Synchronous Rectifier: Yes
• Number Of Outputs: 2
• Current - Output: 400mA
• Frequency - Switching: 100kHz
• Voltage - Input: 6 ~ 30 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 28-SSOP
• Power - Output: 640mW
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: BD9775FV-E2TR

・Internal regulator B
・Oscillator
・Error Amplifier
・PWM Comparator
・MOSFET Driver
2.Channel Control
3.Protection
・Over Current Protection（OCP）
・Short Circuit Protection（SCP）
・Under Voltage Lock Out（UVLO）
・Thermal Shut Down（TSD）
Each output can be individually turned on or off with CTL1 and CTL2. When the CTL is “H” (more than 1.5V), it becomes
turned on.
When detected over current (detecting drop voltage of the main MOSFET’s ON resistance), the MOSFET switch becomes
turned off, and the energy on DTC pin is discharged. After discharged, the output restarts automatically. The level of the
OCP detection threshold can be set by the resistance, which is connected between VCC and CL.
When either output goes down and the voltage on INV pin gets lower than 0.7V, a capacitor placed on SCP is started to
charge.
When the SCP pin becomes more than 2.0V, the main MOSFET switches of both outputs are turned off; then, the outputs are
latched. While they are latched, the IC can be reset by restarting VCC or CTL, or discharging SCP.
Due to avoiding malfunctions when the IC is started up or the power supply voltage is rapidly disconnected, the main
MOSFET switches become off and DTC is discharged when the supply voltage is less than 5.7V. Also, when the output is
latched because of SCP function, the latch becomes reset. Due to preventing malfunctions in the case the power supply
voltage fluctuate at near UVLO threshold, there is 0.1V hysteresis between the detection and reset voltage of UVLO
threshold.
Due to preventing breakdown of the IC by heating up, the main MOSFET switches become off and DTC pin is discharged by
detecting over temperature of the chip. Due to preventing malfunctions in the case temperature fluctuate at near TSD
threshold, there is hysteresis between TSD on and off.
(VCC-5V) is generated from the power supply voltage. The voltage is for the driver of the main MOSFET switch.
Place a capacitor with low ESR (several decades mΩ) between VREGB and PVCC.
Placing a resistor and a capacitor to RT and CT, respectively, generates two triangle waves for both cannels, and each wave
is opposite phase. The waves are input to the PWM comparators for CH1 and CH2. Also, the oscillating frequency can be
slightly adjusted (less than 20%) by putting external clock pulse into Fin pin, which is higher frequency than the fixed one.
It amplifies the difference, between the establish output voltage and the actual output one detected at INV. And amplified
voltage comes out from FB. The comparing voltage is 1.0V and the accuracy is ±2%. The phase can be compensated
externally by placing a resistor and a capacitor between INV and FB.
It converts the output voltage from error amplifier into PWM waveform, then output to MOSFET driver.
The main drivers (OUT1, OUT2H) are for P-channel MOSFETs, and the driver (OUT2L) for synchronous rectification is for
N-channel MOSFET.
configurations are push-pull type.
(Vds=0.4V) for the source current.
（VREGB）
The values of output voltage are clamp to VREGB, VREGA, respectively.
In addition, the output current capability is 36mA for the sink current and 320mA
21/29
All drivers’ output