ISL8206MIRZ Intersil, ISL8206MIRZ Datasheet
ISL8206MIRZ
Specifications of ISL8206MIRZ
Available stocks
Related parts for ISL8206MIRZ
ISL8206MIRZ Summary of contents
Page 1
... CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. | 1-888-INTERSIL or 1-888-468-3774 Intersil (and design registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2009, 2010. All Rights Reserved All other trademarks mentioned are the property of their respective owners. (see page 18) ...
Page 2
... COMP/EN Ordering Information PART NUMBER (Notes PART MARKING ISL8204MIRZ ISL8204M ISL8206MIRZ ISL8206M ISL8204MEVAL1Z Evaluation Board ISL8206MEVAL1Z Evaluation Board NOTES: 1. Add “-T” suffix for tape and reel. Please refer to 2. These Intersil plastic packaged products employ special material sets, molding compounds and 100% matte tin plate plus anneal (e3) termination finish ...
Page 3
Pin Configuration PD1 PD2 PHASE 10 PD3 11 PGND Pin Descriptions PIN SYMBOL PGND Power ground pin for signal, input, and output return path. PGND needs to connect to one (or ...
Page 4
Pin Descriptions (Continued) PIN SYMBOL 13 COMP/EN This is the multiplexed pin of the ISL8204M, ISL8206M. During soft-start and normal converter operation, this pin represents the output of the error amplifier. Use COMP/EN in combination with the FB pin to ...
Page 5
... Thermal Resistance (Typical) GND - 0. 0. QFN (Notes VCC - 0.3V to +15V Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . .see link below GND http://www.intersil.com/pbfree/Pb-FreeReflow.asp Recommended Operating Ratings Input Supply Voltage (V Output Voltage (V P VCC Fixed Supply Voltage . . . . . . . . . . . . . . . . . +5V or +12V Wide Range Supply . . . . . . . . . . . . . . . +6.5V to +14.4V Ambient Temperature Range (T = +25° ...
Page 6
Electrical Specifications T C -40°C to +85°C. (Continued) PARAMETER DYNAMIC CHARACTERISTICS Voltage Change For Positive Load Step Voltage Change For Negative Load Step Voltage Change For Positive Load Step Voltage Change For Negative Load Step CONTROLLER PVCC Supply Current Shutdown ...
Page 7
V IN (+5V/+12V) C (BULK 220µF FIGURE 2. TEST CIRCUIT FOR ALL PERFORMANCE AND DERATING GRAPHS Typical Performance Characteristics Efficiency Performance T C 100 3.3V 2. ...
Page 8
Typical Performance Characteristics Transient Response Performance V OUT I OUT FIGURE 7. 1.5V TRANSIENT RESPONSE V OUT I OUT FIGURE 9. 2.5V TRANSIENT RESPONSE 8 ISL8204M, ISL8206M (Continued +25° 12V VCC C = ...
Page 9
Typical Performance Characteristics Output Ripple Performance V 6A OUT V 4A OUT V 0A OUT FIGURE 11. 1.2V OUTPUT RIPPLE V 6A OUT V 4A OUT V 0A OUT FIGURE 13. 2.5V OUTPUT RIPPLE 9 ISL8204M, ISL8206M (Continued ...
Page 10
Reference Circuitry For General Applications 1. Single Power Supply Figure 15 shows the ISL8204M, ISL8206M application schematic for input voltage +5V or +12V. The PVCC pin can connect to the input supply directly. C PVCC PVCC COMP/EN VIN ISL8204M, ISL8206M ...
Page 11
The COMP/EN will continue to ramp to ~1V. From T , there is a nominal 6.8ms delay, which allows 1 the PVCC pin to exceed 6.5V (if rising up towards 12V), ...
Page 12
If the output is pre-biased to a voltage above the expected value (as shown Figure 22), neither MOSFET will turn on until the end of the soft-start, at which time it will pull the output voltage down to the final ...
Page 13
The overcurrent function will trip at a peak inductor current (I ) determined by Equation 2: PEAK × × SET SET ------------------------------------------- - I = PEAK where the internal I ...
Page 14
~6.8ms ~6.8ms FIGURE 23. OVERCURRENT RETRY OPERATION Starting up into a shorted load looks the same as a retry into that same shorted load. In both cases, OCP is always enabled during soft-start; once it trips, ...
Page 15
In addition to the bulk capacitance, some low Equivalent Series Inductance (ESL) ceramic capacitance is recommended to decouple between the drain terminal of the high side MOSFET and the source terminal of the low side MOSFET. This is used to ...
Page 16
LOAD CURRENT (A) FIGURE 26. POWER LOSS vs LOAD CURRENT (5V 4.0 3.5 3.3V 3.0 2.5 2.5V 0.6V 1.5V 2.0 1.5 1.0 0.5 0 ...
Page 17
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries ...
Page 18
... Initial Release. Products Intersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The Company's products address some of the industry's fastest growing markets, such as, flat panel displays, cell phones, handheld products, and notebooks. Intersil's product families address power management and analog signal processing functions ...
Page 19
Package Outline Drawing L15.15x15 15 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE (PUNCH QFN) Rev 3, 8/10 PIN 1 1 1514 13 12 INDEX AREA 15.0±0.2 15.8±0.2 TOP VIEW 5° ALL AROUND ...
Page 20
Package Boundary 3.00 2.20 1.70 0.90 0.40 0.0 0.0 0.40 0.90 1.70 2.20 3.00 4.00 8.30 TYPICAL RECOMMENDED LAND PATTERN 6.60 4.80 3.40 1.80 0.00 0.60 1.20 2.20 3.70 4.30 6.60 STENCIL PATTERN WITH ...