HW-V5-ML525-UNI-G Xilinx Inc, HW-V5-ML525-UNI-G Datasheet - Page 13

• Manufacturer Part Number: HW-V5-ML525-UNI-G
• Description: EVAL PLATFORM ROCKET IO VIRTEX-5
• Manufacturer: Xilinx Inc
• Series: Virtex™-5 LXr
• Type: FPGAr

Specifications of HW-V5-ML525-UNI-G

• Contents: ML52x Platform, Power Supply, Cables and Documentation
• For Use With/related Products: Virtex™-5 LXT
• For Use With: HW-XGI-SCLK-G - MODULE SUPER CLOCKHW-AFX-SMA-SFP - CONVERSION MODULE SMA - SFPHW-AFX-SMA-SATA - CONVERSION MODULE SMA - SATAHW-AFX-SMA-RJ45 - CONVERSION MODULE SMA - RJ45HW-AFX-SMA-NQSL-G - NQSL NELCO QUAD SERIAL LOOPHW-AFX-SMA-HSSDC2 - CONVERSION MODULE SMA - HSSDC2HW-AFX-BERG-SDRAM - EXPANSION MOD SDRAM BERG-SDRAM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 2: Onboard Regulation: Voltage, Current, Jacks, and Jumpers
ML52x User Guide
UG225 (v2.1) August 4, 2010
Power Supply
VCCINT
VCC33
Name
5V
1. Power Switch
2. Power Regulation
R
Max Current
7.0A / 30.0A
On Position
Off Position
Main Board Regulation
Rating
N/A
3.0A
The board has onboard power supplies controlled by the power switch. When the V5 LED
is lit, this indicates the board is powered.
In the ON position, the power switch enables delivery of all power on the board by way of
voltage regulators situated close to the left side of the board and the MGT power module
situated close to the right side of the board. These regulators feed off the 5V external power
brick or the 5V power supply jack.
The 5V power brick is capable of providing a maximum of 6.5A. For designs that require
greater than 6.5A, an ATX power supply can be connected to the J27 hard drive power
connector.
Note:
controller chip. It is always recommended to check the power supply voltage values before testing
your design or taking measurements.
In the OFF position, the power switch disables all modes of power on the board.
The ML52x platform has onboard regulation for the DUT main power supplies listed in
Table
voltage independently from the bench-top power supply (see
done by removing the power supply enable jumpers for the headers that correspond to
each supply voltage listed in
Note:
•
•
If your design exceeds the maximum current rating for any of the onboard regulators
for any given rail, that rail must be supplied by the external power jack.
The power enable jumper must be removed before supplying an external supply on
its corresponding supply jack.
2. These regulators also have a corresponding input voltage jack to supply each
5V must always be supplied to the board to enable the 3.3V regulator for the System ACE
Voltage
Typical
3.3V
1.0V
5V
Connector
Jack/
N/A
J101
J109
J100
J27
www.xilinx.com
Table
2.
Jumper
Enable
N/A
N/A
J112
Main input voltage for the ML52x boards
supplied through the jack, barrel connector
or Molex connector.
Supplies 3.3V of the System ACE chip and
other onboard circuits.
Core voltage for the FPGA (DUT).
Max current rating:
• ML521 and ML523 boards rated at 7A
• ML525 board rated at 30A
Description
Figure 3, page
Detailed Description
14). This is
13