ATMEGA329P-20MU Atmel, ATMEGA329P-20MU Datasheet - Page 312

• Manufacturer Part Number: ATMEGA329P-20MU
• Description: IC MCU 32K 4X25 LCD CTRL 64-QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA329P-20MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-MLF®, 64-QFN
• Processor Series: ATMEGA32x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SPI, USART, USI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: ATSTK600-TQFP64 - STK600 SOCKET/ADAPTER 64-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ATMEGA329P-16MU; ATMEGA329P-16MU

27.7.16
27.7.17
8021G–AVR–03/11
Serial Programming Pin Mapping
Serial Programming Algorithm
Table 27-16. Pin Mapping Serial Programming
Figure 27-10. Serial Programming and Verify
Notes:
When programming the EEPROM, an auto-erase cycle is built into the self-timed programming
operation (in the Serial mode ONLY) and there is no need to first execute the Chip Erase
instruction. The Chip Erase operation turns the content of every memory location in both the
Program and EEPROM arrays into 0xFF.
Depending on CKSEL Fuses, a valid clock must be present. The minimum low and high periods
for the serial clock (SCK) input are defined as follows:
Low: > 2 CPU clock cycles for f
High: > 2 CPU clock cycles for f
When writing serial data to the ATmega329P/3290P, data is clocked on the rising edge of SCK.
When reading data from the ATmega329P/3290P, data is clocked on the falling edge of SCK.
See
To program and verify the ATmega329P/3290P in the serial programming mode, the following
sequence is recommended (See four byte instruction formats in
1. Power-up sequence:
Apply power between V
Figure 27-11
1. If the device is clocked by the internal Oscillator, it is no need to connect a clock source to the
2. V
Symbol
MOSI
MISO
SCK
XTAL1 pin.
CC
- 0.3V < AVCC < V
for timing details.
CC
and GND while RESET and SCK are set to “0”. In some sys-
Pins
PB2
PB3
PB1
ck
ck
CC
MOSI
MISO
< 12MHz, 3 CPU clock cycles for f
< 12MHz, 3 CPU clock cycles for f
SCK
+ 0.3V, however, AVCC should always be within 1.8 - 5.5V
XTAL1
RESET
GND
(1)
I/O
O
I
I
AVCC
VCC
+1.8 - 5.5V
+1.8 - 5.5V
ATmega329P/3290P
(2)
Table
ck
ck
Serial Data out
Serial Data in
Description
27-18):
Serial Clock
>= 12MHz
>= 12MHz
312