ST72F260G1M6 STMicroelectronics, ST72F260G1M6 Datasheet - Page 109

• Manufacturer Part Number: ST72F260G1M6
• Description: MCU 8BIT 4K FLASH ICP 28SOIC
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F260G1M6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Data Converters: A/D 6x10b
• Processor Series: ST72F2x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C/SCI/SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7F264-IND/USB, ST72F34X-SK/RAIS, ST7MDT10-DVP3, ST7MDT10-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 6-ch x 10-bit
• Controller Family/series: ST7
• No. Of I/o's: 22
• Ram Memory Size: 256Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• For Use With: 497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-4840

I
11.6.5 Low Power Modes
11.6.6 Interrupts
Figure 60. Event Flags and Interrupt Generation
Note: The I
the same interrupt vector (see Interrupts chapter).
They generate an interrupt if the corresponding
Enable Control Bit is set and the I-bit in the CC reg-
ister is reset (RIM instruction).
2
WAIT
HALT
10-bit Address Sent Event (Master mode)
End of Byte Transfer Event
Address Matched Event (Slave mode)
Start Bit Generation Event (Master mode)
Acknowledge Failure Event
Stop Detection Event (Slave mode)
Arbitration Lost Event (Multimaster configuration)
Bus Error Event
C BUS INTERFACE (Cont’d)
Mode
*
EVF can also be set by EV6 or an error from the SR2 register.
STOPF
ADD10
BERR
ARLO
ADSL
*
BTF
No effect on I
I
I
In HALT mode, the I
resumes operation when the MCU is woken up by an interrupt with “exit from HALT mode” capability.
2
2
SB
AF
2
C interrupts cause the device to exit from WAIT mode.
C registers are frozen.
C interrupt events are connected to
2
C interface.
Interrupt Event
2
C interface is inactive and does not acknowledge data on the bus. The I
ITE
Description
ST72260Gx, ST72262Gx, ST72264Gx
ADSEL
STOPF
ADD10
BERR
Event
ARLO
Flag
BTF
SB
AF
Control
Enable
ITE
Bit
INTERRUPT
EVF
from
Wait
Exit
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
2
C interface
109/172
from
Halt
Exit
No
No
No
No
No
No
No
No