MC68HC908JB8JPE Freescale Semiconductor, MC68HC908JB8JPE Datasheet - Page 225

• Manufacturer Part Number: MC68HC908JB8JPE
• Description: IC MCU FLASH 8BIT 8K 20-DIP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC68HC908JB8JPE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 3MHz
• Connectivity: USB
• Peripherals: LVD, POR, PWM
• Number Of I /o: 13
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 20-DIP (0.300", 7.62mm)
• Controller Family/series: HC08
• No. Of I/o's: 13
• Ram Memory Size: 256Byte
• Cpu Speed: 3MHz
• No. Of Timers: 1
• Embedded Interface Type: USB
• Rohs Compliant: Yes
• Processor Series: HC08JB
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: USB
• Maximum Clock Frequency: 3 MHz
• Number Of Programmable I/os: 37
• Number Of Timers: 2
• Operating Supply Voltage: 4 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: Through Hole
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68EML08GZE, KITUSBSPIDGLEVME, KITUSBSPIEVME, KIT33810EKEVME
• Minimum Operating Temperature: 0 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

13.9 IRQ Option Control Register
MC68HC908JB8•MC68HC08JB8•MC68HC08JT8 — Rev. 2.3
Freescale Semiconductor
Address:
The IRQ option control register controls and monitors the external
interrupt function available on the PTE4 pin. It also disables/enables the
pullup resistor on the IRQ pin.
PTE4IF — PTE4 Interrupt Flag
PTE4IE — PTE4 Interrupt Enable
IRQPD — IRQ Pullup Disable
Reset:
Read:
Write:
•
•
•
This read-only status bit is high when a falling edge on PTE4 pin is
detected. PTE4IF bit clears when the IOCR is read.
This read/write bit enables or disables the interrupt function on the
PTE4 pin to trigger the IRQ interrupt. Setting the PTE4IE bit and
clearing the USBEN bit in the USB address register configure the
PTE4 pin for interrupt function to the IRQ interrupt. Setting PTE4IE
also enables the internal pullup on PTE4 pin.
0 = IRQ interrupt requests on falling edges only
1 = Falling edge on PTE4 is detected and PTE4IE is set
0 = Falling edge on PTE4 is not detected or PTE4IE is clear
1 = PTE4 interrupt enabled; triggers IRQ interrupt
0 = PTE4 interrupt disabled
Controls pullup option on IRQ pin
Enables PTE4 pin for external interrupts to IRQ
Shows the state of the PTE4 interrupt flag
$001C
Bit 7
Figure 13-4. IRQ Option Control Register (IOCR)
0
0
External Interrupt (IRQ)
= Unimplemented
6
0
0
0
5
0
0
4
0
3
0
0
IRQ Option Control Register
PTE4IF
2
0
External Interrupt (IRQ)
PTE4IE
1
0
Technical Data
IRQPD
Bit 0
0
225